Cut 15 top boards 5 ft. long and rip them to 3 in. wide with a table saw so the top will glue up flat without the typical rounded edges of 2x4s. For the leg slot, cut two of the top boards into three pieces: a 39-in. middle piece and two 7-in. end pieces. Glue and screw the top together, one board at a time, with 3-in. deck screws, keeping the ripped edge facing up and level with the adjoining boards. Use a corded drill so there’s plenty of oomph to drive each screw below the surface. Note that the third glue-up from each end is where each leg notch is inserted. You can also create a nifty tool tray in the top by notching the three top pieces with a jigsaw. Clamp every 8 in. or so before driving in the 3-in.deck screws. Predrill the screw holes near the ends to prevent splitting. When you’re screwing on the 7-in. long 2x4s to create the leg slots, use a scrap piece of 2×4 as a spacer.
I ended up making a number of practice cuts. The first revealed that I hadn't tightened the screws on the edge guide enough. The second revealed that the design of the edge guide provided very little support at the end of a board, because of the cut-out for the router bit. In the "Getting Started in Woodworking" video, they had screwed a piece of hardwood to the edge-guide, to provide a continuous -- and longer -- bearing surface. I may do that myself, some day, but I didn't have the materials at hand, so I clamped some 2x4 scrap to the end of each board, to provide a continuous bearing surface past the ends. The two grooves in the long stretchers and the side groove in the short stretchers have identical layout. I made practice cuts in scrap until I had the edge guide set correctly, then I cut them all with that one setting. The bottom groove of the short stretchers uses a different setup, so it was back to the scrap, before cutting them.
In this class, John will explain and demonstrate safe spindle turning techniques for turning a bud vase or a carvers mallet, an essential tool for anyone wishing to sculpt wood or make hand made joinery. Objective Through hands-on learning students will gain experience and confidence using our new Laguna mini lathes. You will develop an understanding...
If you don't quite have the space for a real pony, make this handcrafted wood version instead. The horse pictured here is unfinished pine, but there are lots of woods and finishes to choose from. Everything you need comes with the kit, and the plans can be downloaded. If you don't want to build it yourself, you can order from the website—just allow two to three weeks to ship.

A woodworking school teaching furniture making techniques located in Pennsylvania. Beginner through advanced students will learn solid wood furniture construction using traditional and modern techniques. The classes emphasize wood movement, practical methods, efficiency (with machines and hand tools), design, milling, joinery, finishing, and safety. Woodworking and furniture making courses are offered to aspiring crafts men and women throughout the country.

With the top laying on the floor, bottom side up, the next step is to flip the base upside down, and attach it to the top. I followed Asa Christiana's design, in using s-clips. When I stopped by my local Woodcraft, though, they only had two packages of ten, so I didn't use as many as I would have, otherwise. For the top I put four on each side and two on each end. For the shelf I put three on each side and two on each end. If it turns out that I need more, I can always add more.


I made a template by scribing two adjoining squares on a piece of MDF, using compass and straightedge, then marking each corner with a centerpunch, then drilling the points with a 1/16" bit. I find I'm always breaking small bits, so I picked up a couple of each size some months ago, and on looking I found I had three 1/16" bits, which worked fine for what I intended.
An excellent introduction to woodworking is to use crates as your main material. The boxes are already formed, which means less assembly work for you—yet it looks impressive once your project is altogether. With this crate coffee table, you still get to practice your skills adding the casters and the center box. Finish with a little stain, and this table is ready to roll. You can find the full tutorial at DIY Vintage Chic. 
Are you looking for a storage shed, but aren’t quite ready to buy one? Our Rent-to-Own Storage Sheds are the perfect option for you, and they come in a variety of styles. It’s easy to get started–just select your new shed style, color and options, complete the online application here, schedule delivery and you are ready to begin the journey to your storage solution today! * Elite style sheds are not part of Rent-to-Own Storage Sheds. Rent-to-Own Sheds can be chosen up to $10,000.

Out of all the shed books I have read, this book stays by my side while I hammer in the yard. The book is well written by what appears to be a non professional book writer (A Good Thing). It reads as if you are getting advise in laymans terms from your neighbor "The Craftsman", a welcome change from the DIY books, that assume a level of expertese. The level of detail is high and discusses gotcha's, advise, and trade "secrets" that could have only come from years of personal experience building sheds.
×