Ok, I’ve had my morning coffee and now it’s about time to get out to the shop to see what I can do to make that bench a little more pleasing to my eye. I like that Craftsman flair idea. That was my intent at the time I built it, too bad I got lazy and rushed the job. It’s not like I was going to make hundreds of benches for someone else and would never see it again. I should have taken the time to make it the way I wanted it to look. This could keep me entertained for awhile. I see major surgery in the forecast! Gotta plan it all out just right.
Working with wood fresh from the log, this green woodworking project is the perfect introduction to edge tools and wood grain.  In the first week you will produce a three-legged stool using buck and “whip”saws for crosscutting the log to length; wedges and froes for splitting out leg stock; drawknife and spokeshaves at a shaving horse for shaping the legs; and using travishers, rounding planes and specialized rasps for shaping the seat.

For one, the bench itself is a good size. While its width as a tad short at just over 1 ½’, the length is a great 5’ long. Even better, this bench is made out of birch wood. Birchwood is similar to beech in that it is strong but soft enough to prevent inadvertent dulling of your tools. However, birch has a bit of an advantage over beech in that it is not a porous which makes staining on the Windsor Design a more worry-free affair.
Copyright 2018 by Cut The Wood. CutTheWood.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Additionally, CutTheWood.com participates in various other affiliate programs, and we sometimes get a commission through purchases made through our links.
When the holes were complete, I flipped the legs and drilled the countersinks with a 1" Forstner bit. Trying to drill a countersink when the center was already drilled would be impossible with a spade bit or an auger, but Forstner bits are guided by their edges, not their center, so they can handle this job. On thing about Forstners, though -- they have a tendency to skitter around a bit when starting, before they bite. An easy fix for this is to drill a hole through a piece of ply, and to clamp that to your work, creating a jig that will prevent the bit from drilling in the wrong spot.
All-in-all, the Windsor Design workbench is a nice companion, especially if your budget is limited. It is not as deeply designed and perfected as the other two benches, as there is only one vice, the bench dog holes are drilled through the surface (allowing debris to fall to the top drawers) and the drawers can be a little flimsy if you are not using glue for assembling it, but for the price they offer, there are plenty of perks.
Some tools required for this project are hole saw, drilling machine, pencil, tape measure, clamps, etc. This tutorial explains every step properly with images so that anyone can make a wooden sofa sleeve easily. Those, who prefer a video tutorial, can visit the below link to a YouTube video that illustrates the process of building a DIY Sofa Sleeve Cupholder.
Every single person in the class was a novice when they walked in. We all made mistakes at some point, yet none of us really ever felt bad about these hiccups. Inevitably, Bob turned these mistakes into problem-solving opportunities where we could explore new ideas. So what if one morning I skipped coffee and accidentally spent 10 minutes drilling random-ass, pointless domino mortises in the middle of my bench legs? 4 dominos, some sawdust and glue, a little bit of sawing and sanding-- I've got four new inlays on my legs and nobody's the wiser. Not only do I now know how to roll with the punches when building something, but I've got a bench that's uniquely mine AND I don't feel like an idiot. And that last part is a serious feat.

With the Grain: A Craftsman’s Guide to Understanding Wood by Christian Becksvoort. A little knowledge about trees goes a long way toward improving your woodworking. You don’t need a degree in dendrology to build a desk. But you do need intimate knowledge of how our raw material grows and – more importantly – how it responds to its environment after it has been cut and dried.
Before joining the top to the base, loosen the bolts and screws on the lower stretchers to create a little play in the leg posts. Align the top notches with the leg posts and tap the top into place with a hammer and piece of scrap wood, working evenly around the table until all leg posts are level with the tabletop. Tighten the lower stretchers and you’re done. A hefty thanks to Doug Merrill for this weighty idea.
Though still straightforward in design, this bench distinguishes itself from many of its competitors with the sheer wealth of storage options. It includes two drawers of equal size with an additional drawer of double size as well as a spacious cupboard. Altogether, this provides for more storage space and organization than any other workbench we reviewed. Of course, this bench also comes with many of the same advantages and disadvantages that you would expect to see on other models within this lineup.
I made a low table out of a couple of step-stools, my hollow-core door, and one of the MDF panels that would eventually form part of my top. I was concerned that any oil that dripped on the door might interfere with its glue adhesion, when I finally get around to the project for which I'd purchased it. The top side of the top sheet of MDF, though, I planned to oil, anyway. (Ditto for the bottom side of the bottom sheet.
Drilling a precisely positioned, deep, wide hole isn't easy, without a drill press. So I bought a WolfCraft drill guide. After experimenting with it, and drilling some test holes, I build a jig around it. I screwed it to a scrap of MDF, and then drilled a carefully-centered 3/4" hole. The MDF can be clamped more easily than the base itself, and the 3/4" hole will keep a 3/4" Forstner bit drilling precisely where it is supposed to.
I'd intentionally made it oversize, intending to trim it flush. Trimming is a little more complicated than usual, because I needed to trim it flush on two faces. The end face extended a good 3/8", so I cut off most of the excess with a circular saw and the edge guide, then flipped the edge guide upside down to make a stable platform for the router. Aside from the use of the edge guide, flush trimming the edge face was unremarkable.
For most of the course, we'll be heavily focused on developing your skills using hand tools. As a developing woodworker, there is no substitute for putting in the hours of direct hands on practice it takes to gain an intuitive understanding of wood. The early part of this course focuses on working with hand tools as we believe they bring you closer to wood as a material.  You can rip a board on a table saw with out much thought to the wood itself, but you will understand much more about grain if you rip a board with a hand saw.  As the course progresses, machine processes are introduced as a pragmatic aid in expediting projects.  

I'd intentionally made it oversize, intending to trim it flush. Trimming is a little more complicated than usual, because I needed to trim it flush on two faces. The end face extended a good 3/8", so I cut off most of the excess with a circular saw and the edge guide, then flipped the edge guide upside down to make a stable platform for the router. Aside from the use of the edge guide, flush trimming the edge face was unremarkable.
This course will drill deep into the basics, beginning with a firm foundation in understanding wood as a material and incorporates introductory training in a wide range of techniques. You'll leave with a in depth experience of hand tools, practice applications of joinery methods, consider choices for wood selection and working with non-toxic materials, and understand practical planning for designing and executing woodworking projects.  The curriculum focuses on imparting skills through a series of projects designed to build on one another in techniques and complexity. 

As you can see in the image, this shelf goes on both sides of the corner wall. It looks beautiful and can be used to organize books, trophies, pictures frames and many other things. The strength and design of the shelf depends on how properly you build it. First time workers definitely need some guidance to help them with the process. Therefore, I am including this basic video that I found on YouTube that demonstrates the process of making corner wall wooden shelves.


This is used to secure workpieces in place while you work on them – often for jointing. The location and capacity are the important things to look at. Most vices will come on a right-hand configuration either on the front or the side of the bench. If possible, it is a good idea to look for vices that can be repositioned. In terms of capacity, anything over 5” is solid while anything under 4” is likely a bit too small for all projects.
The front edge of a woodworker’s bench is usually lined with square holes positioned at regular intervals. These holes hold bench dogs and holdfast clamps in place for securing work pieces. Beneath the top of the bench, some cabinetmaker models feature single storage drawers, others several drawers and even cupboards incorporated into a case-like base.
to allow 9' at the peak, I like a "shed style" roof, but that may not fly in your HOA.I'd put double doors on or one large one, pour a slab, or use patio blocks then lay down Wolman. plywood for a floor, I would use foam insulating board everywhere I could, walls, floor and ceiling. A few bin type windows or sliders would let in light and fresh air. If you can't get away with your wiring idea, I would use a HD 30 amp twist lock extension cord with an "outside weatherproof outlet" mounted on the home professionally installed for code, 2- 8' long flouresent lights, and a 20 amp outlet inside for a heater and dehumidifier. Dehumidifiers draw about 5-6 amps. You might be better off with a small 6000 BTU window or wall mounted AC unit,( $100 on sale at the Depot), it will take the moisture out of the air and cool it as well in the summer. I'd use thin wall conduit around the shop with about 4 double duplex boxes. You may be able to bring 220v. in and then split into 2-120v circuits. If you make ANY dust in this confined space you must first catch it with a shop vac, then filter the air, and wear a mask. A bathroom ventilator fan would exchange the air and be quiet. A slab in front would allow sawing outside weather permitting. A roll up canopy over the door way would provide "shade" and rain protection. I know this sounds like a lot of work, but I know you can do it if you try. You can get plenty of "free" advice here and from an expert close to you. My neighbor enlisted the help of a handyman for building his 2 sheds and they became friends and did tool swaps and labor trades for time worked. My advice to you.. go 4 it! bill
×