Raphael Berrios is one of our Foundations of Woodworking scholarship students in Spring 2016. He also took our Timber Frame Tiny Home course and brought home one of the structures to finish for himself (you can follow his progress on his blog! Here’s what he had to say about what led him to PTSW, his experience so far, and thoughts for the future:
Great advice. May I add #11?…if you’re left handed (like me), build a left handed bench. It sounds obvious, but when I made my bench, I had looked at all the pictures in my books, laid out plans for a nice, traditional bench, built it, then realized my front vise should have been on the other end (I have no tail vise). I plane from left to right, and the front vise is always in the way.
Let me see if I can come up with a couple details. The table saw is a TS3660. So I have heard, this should be the center of your shop. My jointer is a 6 1/8" Jointer / Planer JP0610 which is 45 inches in length. My router table is the kreg router table that takes up a 24 x 32 inch footprint. My bench is roughly 30 x 70 inches and my bandsaw is 3' x3'. I have other tools as well such as a portable 12.5 Delta thickness planer in addition to a wall mounted dust collector. To add to the list, I am just about to get a 10 inch makita sliding compound miter saw. I can see how space will be eaten up quickly. Any ideas as to how arrange these tools in such a small shop? I will get pics a soon a I
You can transfer a graphic on any wood piece of your choice, including a frame, top of a table, etc. The surface should be clean and big enough for the graphic paper. I am also sharing a video tutorial here that explains in detail the process of transferring any graphic to a wooden surface using a freezer paper. Just gather the items you need and follow this video to carve your favorite designs on your favorite wood items.
Another awesome thing about this coffee table is that it is also has a storage unit. So you can store drinks, and other stuff in the half barrel of your table and then close or open it whenever you need. Pete has also constructed a video for this tutorial for which you can find the link below. It illustrates the same process in a video guide that shows you the exact process to be followed while building this whiskey barrel coffee table.
This place is great! They offer safety classes before you sign up for a membership, and the workspace is big and well maintained. I needed some basic lessons with table and band saws, which went great. I didn't ultimately get a membership because my sawing needs are very specific, and ended up getting a small bandsaw for myself at home. But if you're someone who needs the whole range of tools, this is the place to be!
Much like the dimensions of a bench’s tabletop, the weight capacity will similarly affect what size of projects you can work on with your bench. A common weight capacity sits between 220 to 250 pounds. While this is okay, it will limit some heavier projects. Ideally, you should shoot for 300 pounds, though some benches can offer 500 pounds of weight capacity or more.
Place sounds amazing. Receptionist was rude. Sarcastic remarks were not necessary. I called regarding the private lessons. And was told that they "can't hold my hand to do the work". The person made the statement not allowing me to finish saying that I have experience with wood work. I was really upset by the statement. He did not seem interested in having me as a client/student.
A better solution would have been to route a rabbet into the side, so that the added strip always had thickness. The way I did it means that the strip I glued in is very narrow, and hence very weak, at a certain point. In this case, that's not a problem, because it's going to be sitting under the countertop layer. I also noticed that because I had only clamped the strip down, and not into the edge, there was a noticeable glue gap where the strip butted up against the MDF. Again, in this application it isn't visible. But if I was doing something like this on the top of a table, I'd make sure to cut a clean rabbet, and to clamp both down and in.
The bench would end up being about 5 feet long. I thought about cutting 5 feet out of my 8 feet long countertop and use the rest for a small support table. However, after a consideration, I decided to bypass the front vise altogether together with the overhang so my bench will be 4 feet long. This allows me to skip the MDF and just glue the two halves of the 8 feet board together.
A workbench needs to be heavy enough that it doesn't move under you while you're working, and stiff enough that it doesn't rack itself to pieces under the forces that will be placed upon it. It doesn't take many hours of planing a board or hammering a chisel for a worktable made of nailed 2x4s to come apart. Traditional bench designs use mortise-and-tenon joinery, which is strong and rigid, but not really suited for a novice woodworker who doesn't already have a bench.
Applying the oil is easy. Put on some vinyl gloves, pour some oil in a bowl, take a piece of clean cotton cloth the size of washcloth or smaller, dip it in the oil, and apply it to the wood. You want the wood to be wet., you're not trying to rub it in until it's dry. Apply oil to the entire surface, and then go over it looking for dry spots, applying more oil as needed. After fifteen minutes of keeping it wet, let it sit for another fifteen minutes. Then apply another coat of oil, and let it sit for another fifteen minutes.
Chris I blame you for all these altars that are being built today and now you thinks we over thinks ’em–huh. You whipped the masses into a frenzy— now Woodworkers are trying to out pretty each other–out wood species each other –out Rube Goldberg each other. I made 2 benches in 30 years neither had a through dovetail but many were made on them and I have no idea but I would bet a dollar that neither weighed 280 pounds but they both had tons of wood on them. If you want the bench as a destination god bless but it was intended as a mean. Thats my rant I could be wrong
Evidence of a removed fireplace makes it clear that the woodworkers were doing tasks that required warmth, like using glue. The type of glue used during that time had to be heated to a certain temperature. Bill Flynt, a former colleague of Garrison, tested the wood of the shop and found that it is second- or third-generation wood, meaning that New Englanders had already cut down and replanted lots of trees by that time.
Next is the shelf. Start with the 24x48" piece of MDF. Clamp this on top of the base, and pencil in the outside of the stretchers and the inside angle of the legs. Flip it over, pull out your trusty cutting guide, and cut it to width and to length. Cutting out the angles is simple, with a jig saw. It's not much work with a hand saw. If you took enough care with supporting blocks and stops, you could probably do it with a circular saw. Since I did have a jig saw, I used it.