This is another example of small woodwork projects that require good time and woodworking skills. This item is built using multiple wooden parts. Each part is shaped in a specific design and then all parts are attached together to make the final TV set. I have never tried building this one, mostly because I don’t own an iPhone, but also because making this item is not an easy task. By the way, it works fine with all kinds of phones.
One aspect of the Windsor Design that is hit or miss is the vice. Notice we have to use the singular when describing it because this is the first workbench that we have reviewed which features only one vice. To make matters more frustrating, the vice cannot be repositioned along the bench. That said, the vice does at least have the largest capacity out of any we reviewed. At 7” capacity, the Windsor Design vice can secure any size workpiece you may have.
As soon as I came across this tutorial, I didn’t wait any longer to start building one. Some of the items you need for this project are hardwood plywood, saw, glue, nails, drilling machine, etc. The video is very easy to follow for anyone with basic woodworking knowledge and experience. The first source link also includes a step by step procedure in plain English for those, who are not comfortable enough with the video tutorial.
All-in-all, the Windsor Design workbench is a nice companion, especially if your budget is limited. It is not as deeply designed and perfected as the other two benches, as there is only one vice, the bench dog holes are drilled through the surface (allowing debris to fall to the top drawers) and the drawers can be a little flimsy if you are not using glue for assembling it, but for the price they offer, there are plenty of perks.
Next is the shelf. Start with the 24x48" piece of MDF. Clamp this on top of the base, and pencil in the outside of the stretchers and the inside angle of the legs. Flip it over, pull out your trusty cutting guide, and cut it to width and to length. Cutting out the angles is simple, with a jig saw. It's not much work with a hand saw. If you took enough care with supporting blocks and stops, you could probably do it with a circular saw. Since I did have a jig saw, I used it.
Flip the base upright, put the MDF on top of it, then use a straightedge to draw two straight lines joining the outside edges of the legs and extending the width of the MDF. I used the countertop as the straightedge. We cut it with our cutting guide, which is based on the factory edge of a sheet of 1/4" plywood, so it should be straight enough. Use a carpenter's square to transfer these lines onto the ends of the MDF.
My first shop was a 8 x 10 ft room, actually a bedroom, with 10 ft high ceilings in a older home in Chicago. I had a 10" Craftsman TS, drill press, 8 1/4" Skil saw which still works, some welding tanks, hand tools and... my bed was a loft across the 10 ft length 4 ft down from the ceiling with a ladder against the wall to get up. I was 16 yrs old then, now I am 66 yrs, have 2 shops with Craftsman power tools up stairs, and Grizzly tools ,a Powermatic 68, a MIG welder, and other tools on the ground floor. I've come a long way, You think? I remember making bases for sculptures called "plinths", my first commission, in the living room, 5 pieces rather large, several ft long and wide. The house was haunted, and my mom told the "spirit" to leave and go back downstairs. There was a cold draft and the straw chair would rustle with no one sitting in it. Wow, does that bring back memories from the '60's.
It has been a while since I have posted last, but I do have a question I am pondering. A close family friend has offered to buy me a shed (16 x 12). It looks nice. Double doors, two front windows, vinly siding, and hopefully a ridge vent. Currently I am based in my basement with enough room for my Rigid table saw, bandsaw workbench, some cabinets with very little room for my hand tools, so I used a wall with peg board, and my jointer. My dust collection hangs on the wall as well. (I am being moved outside to free up space in the basement) It is very cramped, but it works. My question is, do wood shops work outside? I know to take precautions of moisture and heat (insulation, dehumidifier, heat for cold season, and so on) but how often to shed workshops work out? Anyone have any ideas on how to keep my tools safe and secondly, does 16 x 12 sound like enough room? Please, I would love some friendly advice.
Some posts may contain affiliate links. BestToolExpert.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for website owners to earn advertising fees by advertising and linking to amazon(.com, .co.uk, .ca etc) and any other website that may be affiliated with Amazon Service LLC Associates Program.
Learn to use hand and power tools to shape wood into objects that will last for decades. You’ll learn about the properties of lumber, safe tool use, measurement and layout, and fundamental woodworking joints. At the end of this week-long course, you’ll leave with an end-grain cutting board, a mitered corner box, and the skills to build an unlimited range of wooden objects.