2. Did I mention the rain here? How is your shed built? Are flooring and walls sealed to prevent water blowing and leaking in? When we get our summer thunderstorms the winds can whip up the rain pretty good and I even have to make sure garage door is closed sometimes. The shed??? Yea. it gets wet inside no matter how much caulk I use on floor gaps. Mine is on slab and shed not really designed to be waterproof. That being said, even if I got floor sealed it still lets some water in where walls meet roof. Not lots but makes for extreme humidity (or dew point if you prefer) levels.
After you have all the holes clean, set things up for your glue-up. You want everything on-hand before you start - drill, driver bit, glue, roller or whatever you're going to spread the glue with, and four clamps for the corners. You'll need a flat surface to do the glue-up on - I used my hollow core door on top my bench base - and another somewhat-flat surface to put the other panel on. My folding table was still holding my oak countertop, which makes a great flat surface, but I want to make sure I didn't drip glue on it so I covered it with some painters plastic that was left over from the last bedroom we painted.
Great advice. May I add #11?…if you’re left handed (like me), build a left handed bench. It sounds obvious, but when I made my bench, I had looked at all the pictures in my books, laid out plans for a nice, traditional bench, built it, then realized my front vise should have been on the other end (I have no tail vise). I plane from left to right, and the front vise is always in the way.
I had a similar experience with running electrical power to a shed. It turned out that I could build a 12x12 shed without a building permit as long as I did not run utilities, but getting a permit opened a whole new set of requirements that forbid me from having a shed at all. And when the nosey old woman next to me kept calling the building inspector on me, it was suggested that I could run an extension cord out to the shed anytime I wanted as long as it wasn’t fastened in a permanent manner.
At Costco, we understand that when you’re looking for a shed or barn, you’re not just looking for a space to store your tools, you’re looking for a structure that’s reliable, sturdy, and weatherproof. This kind of quality assurance is especially important when your shed or barn isn’t just a toolshed, but a place for storing your memories or working on projects. At Costco.com, you’ll find sheds and barns of all shapes, sizes, and materials. Shop by brand, color, or features, and rest assured, knowing that whatever structure you choose, you’re getting it at the best possible price!
Great advice. May I add #11?…if you’re left handed (like me), build a left handed bench. It sounds obvious, but when I made my bench, I had looked at all the pictures in my books, laid out plans for a nice, traditional bench, built it, then realized my front vise should have been on the other end (I have no tail vise). I plane from left to right, and the front vise is always in the way.

The Practical Woodworking course at the JD Lohr School of Woodworking is a complete and comprehensive woodworking course held in our shop on the 13-acre farm in southeastern PA. This is total immersion woodworking for ambitious, interested adults. With class size limited to 11 students and 3-4 instructors in each class, all needs of every student are met regardless of experience level. If you are self taught with no formal training as a woodworker, this course will quite literally change the way you work.


This is one of those things that you never know you need unless you have one. This amazing wooden sofa sleeve works perfectly on either or both sides of a sofa set. It gives your sofa a nice look. The sleeve can also be modified to include a cup holder, mobile holder, etc. You can easily find this item on any online furniture store, but an even better idea is to build one. This way, you can make a sofa sleeve design that you actually like and make space for cup and other things.
Timberframing is a traditional technique for building large and small structures using only wooden joinery. Prized for its structural integrity and beauty, as well as reliance on hand skills, timberframing is regaining popularity in modern applications. We will start with an overview of the different styles and aesthetics involved, and move into the specific tools that are used to lay out and cut the strong joints. Each student gets guided practice time making sample joints. We will all work together to make a small structure that can be raised on the final day of class.
This class is open to novice woodworkers and to more experienced woodworkers who would like to broaden (or simplify) their approach to woodworking. What do we mean by novice? We think it means you are a person who has decided to commit to learning new skills; to growing a passion for the craft of working with wood; and has a strong sense of the limitations of your own knowledge.
Every piece meets the highest grading standards for Every piece meets the highest grading standards for strength and appearance. This lumber is for a wide range of uses from framing of houses to basic interior finishing applications. Boards can also be used for carpentry hobbies furniture shelving and general finish work. This lumber can also be used in ...  More + Product Details Close
Much like the dimensions of a bench’s tabletop, the weight capacity will similarly affect what size of projects you can work on with your bench. A common weight capacity sits between 220 to 250 pounds. While this is okay, it will limit some heavier projects. Ideally, you should shoot for 300 pounds, though some benches can offer 500 pounds of weight capacity or more.
Frame making may look simple but it is a skill that escapes many. For a frame to properly do its job it has to be perfect, any mistake can be a distraction that takes away from the artwork it surrounds. This class will focus on skills essential to making square or rectangular frames. Skill building concepts will include how to break down and mill...
For most of the course, we'll be heavily focused on developing your skills using hand tools. As a developing woodworker, there is no substitute for putting in the hours of direct hands on practice it takes to gain an intuitive understanding of wood. The early part of this course focuses on working with hand tools as we believe they bring you closer to wood as a material.  You can rip a board on a table saw with out much thought to the wood itself, but you will understand much more about grain if you rip a board with a hand saw.  As the course progresses, machine processes are introduced as a pragmatic aid in expediting projects.  
Another awesome thing about this coffee table is that it is also has a storage unit. So you can store drinks, and other stuff in the half barrel of your table and then close or open it whenever you need. Pete has also constructed a video for this tutorial for which you can find the link below. It illustrates the same process in a video guide that shows you the exact process to be followed while building this whiskey barrel coffee table.
A woodworker's Workbench is a special type of bench designed to hold your work when you are working on a wood project. The main purpose of this table is to keep the woodwork steady and to prevent it from moving. Follow the tutorial below to build yourself a nice workbench suitable for your specific woodworking projects. Make sure to modify the table to fit your specific requirements.
Every piece meets the highest grading standards for Every piece meets the highest grading standards for strength and appearance. This lumber is for a wide range of uses from framing of houses to basic interior finishing applications. Boards can also be used for carpentry hobbies furniture shelving and general finish work. This lumber can also be used in ...  More + Product Details Close

I got this idea from a Pinterest post. The final product looks so beautiful that I just couldn’t wait to make one for myself. This was somewhat a different experience from my other regular DIY projects as it doesn’t involve making something from scratch, but turning an existing wood piece into another one. Nonetheless, I enjoyed it very much and the final product was very satisfying. The tutorial I used is linked below.
Our stationary equipment runs the complete range from heavy-duty industrial machines, to inexpensive home shop type of tooling so that each student can compare and contrast the range and versatility of equipment at a wide variety of price points.  We spend time on what makes a good machine good, an adequate one adequate, and a lousy machine worthless. We have no commercial sponsors and will share our opinions based on our experiences regarding the quality of one manufacturer over another.  There is no better place to kick the tires on a variety of equipment than at our shop.     
Glue up the trim on the end, first. Do a dry fit, first, then as you take it apart lay everything where you can easily reach it as you put it back together again, after adding the glue. To help keep the edge piece aligned, I clamped a pair of hardboard scraps at each end. I used the piece of doubled MDF I'd cut off the end as a cawl, to help spread the pressure of the clamps. Squeeze some glue into a small bowl, and use a disposable brush. As you clamp down, position the trim just a little bit proud of the top surface.

Building a Wooden Office Desk Organizer is an easy task for a professional woodworker, but not so much for normal people like you and me. But that doesn’t mean you cannot do this. Two years ago, I had almost no woodworking experience, but now I make most of my household and office wooden items by myself. This saves me a lot of money. And believe me when I say this; you can also manage to make wonderful wood items with a little practice and some woodworking experience.

To mark the centerline, set a compass to span something more than half the width of the leg. Draw an arc from corner of the leg. The point where the arcs intersect will be on the centerline. With a centerline point on each end of the leg, place a scribe on the point, slide a straightedge up to touch the scribe. Do the same on the other end. When you have the straightedge positioned so that you can touch both points with the scribe, and in each case it is touching the straightedge - without moving the straightedge - scribe the line. Use scribes, rather than pencils or pens, because they make more precise marks.
Looking for a great gift for a friend or family member or maybe a Christmas gift? Recommended woodwork projects include a turned wood box with a lid or how to make a jewlery box. New to woodworking? Great! Check out these simple beginner’s woodworking projects. No matter the DIY woodworking project you can find your next gift idea in the wood craft videos listed below.
With the shelf secure, get a couple of friends to come help, and stand the bench on its feet. I said earlier moving the top by yourself is dangerous. Trying to lift the entire bench is foolhardy. Of course, I already said I'm stubborn, so I did it myself by rigging a simple block-and-tackle using lightweight pulleys I got at the hardware store. (Not the lightest-weight pulleys, those are meant for flag poles and have a design load of something like 40 pounds. These had a design load of 420 pounds.)
Although many hand tool operations are thoroughly covered, this is a machine based woodworking experience. You will find the school finely equipped with four table saws, four jointers, three drill presses, three thickness planers, a wood lathe, full dust collection, bandsaws, jig saws and scroll saws, 5 routers and dozens of router jigs and accessories. There is a heavy focus on the safe and efficient use of the table saw starting with it's basic operation and going into advanced production procedures. We consider the table saw to be an essential machine for efficient, accurate, and safe woodworking.

Thanks Chris! I found this page while looking for a link to your e-mail address. I recently finished your erudite volumes on workbench design, and am about to embark on my own bench inspired by your take on the Holtzapffel design. As my vices and planer arrive, I’ve been agonizing over whether to use SYP or rough maple for the top. I don’t have a big budget, so all-maple is not an option. But after reading your ten tips here, I’ll stop agonizing — all SYP it is! This is, after all, my first of what I hope are at least several handmade benches. Your scholarship and craftsmanship are truly inspiring.
Isn’t this amazing that instead of having to throw that old furniture piece away, you can now reuse it to build something even more beautiful? If you do not like this particular idea, there are many other re-purposeful furniture items you can build from an old dresser. Just search the internet for other DIY project ideas. Here is a link to the video tutorial that explains the same procedure in a more practical manner that you can easily follow through.
Learn to use hand and power tools to shape wood into objects that will last for decades. You’ll learn about the properties of lumber, safe tool use, measurement and layout, and fundamental woodworking joints. At the end of this week-long course, you’ll leave with an end-grain cutting board, a mitered corner box, and the skills to build an unlimited range of wooden objects.
My advice? Don't do this. If you have jointer and a planer, use them. If you don't, seriously consider using dimensional lumber that has already been planed and sanded. If you are going to try to clean up construction lumber by hand, using a hand plane is a lot faster and more pleasant than using a belt sander. Except, of course, that to do a good job of planing a board you need a solid bench to hold the board, and you don't have a bench, yet.
The Classic Workbench is simple to use. The leg vise is used primarily for working the edges of boards and the ends of narrower boards. This is self explanatory. To work the faces of boards along the grain, tap up the planing stop (don’t make it any higher than necessary) and butt the end of the board into the teeth of the stop. With the right technique you can plane across wide boards without repositioning the board. You usually don’t need to tap the opposite end of the board to engage it with the stop, but in some cases, especially with rougher stock, you may need to give a tap with your mallet. Working the faces of a stack of boards is extremely quick with the planing stop since you don’t have to open and close a vise constantly. To work across the face of a board, make yourself a doe’s foot and position it at the back corner of the board, holding it down with a holdfast. The doe’s foot is simply a piece of wood with a V-shaped notch cut into one end. The bottomsurface of the doe’s foot can be lined with sandpaper or Crubber to help it stay put on the bench top. To work long boards, fasten a batten to the right leg with a holdfast and use that to support the end of the long board. We’ve found that a deadman is not necessary for the majority of work, especially on a bench of this length. For working the ends of smaller boards the leg vise can be used, but for precision work like dovetailing, we use and recommend our Moxon Vise.

As soon as I came across this tutorial, I didn’t wait any longer to start building one. Some of the items you need for this project are hardwood plywood, saw, glue, nails, drilling machine, etc. The video is very easy to follow for anyone with basic woodworking knowledge and experience. The first source link also includes a step by step procedure in plain English for those, who are not comfortable enough with the video tutorial.
In the Port Townsend School of Woodworking’s twelve-week Woodworking Foundation course, you will learn the essential skills, tools and mindsets of the traditional joiner. This is NOT an industrial arts course with a focus on machinery and production processes. Rather, it is a course in PRE-industrial artisanship--the creation of individual works through mostly hand tools and skills.. 
For the router you'll need a a 3/8" straight bit, an edge guide, 1/4"- and 1/8"-radius roundover bits, and a flush-trim bit with at least a 1-1/2" cutting length. Bits of this size are available only for a 1/2" collet. Some routers are capable of using multiple collet sizes. I was fool enough to buy a router that only had a 1/4" collet. More on that, later.

I used the factory edge of the half-panel of hardboard as a guide for cutting the ply. I wanted to cut a 5-1/2" strip, and my saw cuts 4-1/2" from the edge of the shoe, so I wanted the edge of the hardboard 10" from the edge of the ply. So I set my combination square to 10", and used it to mechanically set the distance. Hint - if you need two things to be precisely the same length, try to avoid measuring them separately. Use some mechanical mechanism for setting the distance.
For one, the bench itself is a good size. While its width as a tad short at just over 1 ½’, the length is a great 5’ long. Even better, this bench is made out of birch wood. Birchwood is similar to beech in that it is strong but soft enough to prevent inadvertent dulling of your tools. However, birch has a bit of an advantage over beech in that it is not a porous which makes staining on the Windsor Design a more worry-free affair.
Those bums even have a stipulation that you can't connect any utilities to a shed. My plan is to adhere to the letter of the law if not the spirit. I plan to run a buried 20 amp power line out to the shed (this will be done professionally and properly according to whatever is required by the law), but it will require a manual connection to a junction box on the outside of my house to complete the circuit. That way, I can argue that the electrical connection is only temporary and is little more than a safe and buried version of an extension cord.
×