With the Grain: A Craftsman’s Guide to Understanding Wood by Christian Becksvoort. A little knowledge about trees goes a long way toward improving your woodworking. You don’t need a degree in dendrology to build a desk. But you do need intimate knowledge of how our raw material grows and – more importantly – how it responds to its environment after it has been cut and dried.
MechanicGuides.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for website owners to earn advertising fees by advertising and linking to amazon(.com, .co.uk, .ca etc) and any other website that may be affiliated with Amazon Service LLC Associates Program. Amazon and the Amazon logo are trademarks of Amazon.com, Inc. or its affiliates.
Cut 15 top boards 5 ft. long and rip them to 3 in. wide with a table saw so the top will glue up flat without the typical rounded edges of 2x4s. For the leg slot, cut two of the top boards into three pieces: a 39-in. middle piece and two 7-in. end pieces. Glue and screw the top together, one board at a time, with 3-in. deck screws, keeping the ripped edge facing up and level with the adjoining boards. Use a corded drill so there’s plenty of oomph to drive each screw below the surface. Note that the third glue-up from each end is where each leg notch is inserted. You can also create a nifty tool tray in the top by notching the three top pieces with a jigsaw. Clamp every 8 in. or so before driving in the 3-in.deck screws. Predrill the screw holes near the ends to prevent splitting. When you’re screwing on the 7-in. long 2x4s to create the leg slots, use a scrap piece of 2×4 as a spacer.
A steam box and a heat source are the two main components used to steam bend wood. Steam boxes must be able to withstand large fluctuations in temperature and humidity without breaking apart. In this two-hour workshop, students will build an optimized steam box that can last through the tough job of steaming wood, allowing them to continue creating their own projects at home!
What I did, when I came back, was to clamp down the strip where it had torn away, and then to start routing from the other end. I still moved the router from right to left, but I did it in six-inch sections, taking light passes, and sort of whittled the strip flush. As the sections I was working were farther to the right, the strip was thinner. Eventually I came to where I was trimming the strip away entirely, at which point I took off the clamps and the remainder fell away.

What I did, when I came back, was to clamp down the strip where it had torn away, and then to start routing from the other end. I still moved the router from right to left, but I did it in six-inch sections, taking light passes, and sort of whittled the strip flush. As the sections I was working were farther to the right, the strip was thinner. Eventually I came to where I was trimming the strip away entirely, at which point I took off the clamps and the remainder fell away.
For most of the course, we'll be heavily focused on developing your skills using hand tools. As a developing woodworker, there is no substitute for putting in the hours of direct hands on practice it takes to gain an intuitive understanding of wood. The early part of this course focuses on working with hand tools as we believe they bring you closer to wood as a material.  You can rip a board on a table saw with out much thought to the wood itself, but you will understand much more about grain if you rip a board with a hand saw.  As the course progresses, machine processes are introduced as a pragmatic aid in expediting projects.  
The base needs to be as wide as the sum of width of the guide strip and the distance from the edge of the shoe, plus a bit extra, With my saw, the overhang is 3-1/2", so I made my guide strip 5-1/2" wide. The distance between from the edge of the shoe to the blade is about 4-1/2", so the base needs to be at least 10" wide. Since I was working with a 24" wide sheet, I just sliced it down the middle.
The Meridian 8 ft. x 10 ft. wood The Meridian 8 ft. x 10 ft. wood storage shed kit from Handy Home Products is pre-cut and easy to assemble with common household tools. It features 9 ft. peak wall height with treated engineered siding that prevents rot and is pre-primed and ready to paint (paint sold separately). The ...  More + Product Details Close
Dip your toes in the world of woodworking with our week-long courses, and by the end of the week, you'll be swimming. During these intensive, week-long woodworking courses, you will benefit from the guidance of our expert furniture makers, learning the basic principles of woodwork and cabinet making to professional standards. Hone your technique with our classes and create precise, beautiful work with our expertise, equipment and advice at your disposal.
Who doesn’t want to have one awesome and handy wooden desk organizer that not only looks beautiful but can store all your mini office desk items properly? See the picture below. I am sure you will love this one. I have already built one myself as I just could not resist having one at my office. This thing easily stores all my office desk essentials, including pen, pencils, marker, small notebooks, etc. in the most organized way. You can see it yourself.
My first attempt at making a cutting guide didn't work. What I ended up with worked fine for cutting panels, but the guide-strip was too narrow, and when the saw was extended fully for rough-cutting the 4x4's the clamp heads got in the way. So I made another. Actually, I made two more, so that I could cut one into shorter pieces that would be easier to handle.
A bottle carrier is a bucket like carrier used to carry beer bottles and so. Yes, the same one you must have used to carry your six-pack. Drinker or not, a bottle carrier is a useful item for everyone. It can be used to carry around or store small items around a household. And it is also very easy to build one. I have several of these lying around my house. Also known as wooden beer totes, this is one wood item you will absolutely love to make. It is also super easy to build.

Rocking horses, toy chests and dollhouses are just a few of the classic gifts generations have treasured. Now you can give all the pint-sized DIYers on your list those same classic gifts, and make them yourself with the help of these DIY toy kits. They're perfect for kids of all ages, and will be treasured for years to come. The best part? All these gifts can still make it to your door by Christmas.
One quality about this bench that is definitely lacking is space – both tabletop and storage. The Olympia Tools does provide an adequate shelf, but it does not come with any drawers, nor does it offer the option of adding them later. The table top is the smallest we saw at 50” long and 2’ wide, though the width is actually better than most of the other table we reviewed. Still, a significant chunk of that width is occupied by a trough. This trough is designed to hold smaller workpieces to keep them from falling or getting knocked over, but it removes about 6” of width from the tabletop.
Over the years, the editors at The Family Handyman have built nearly a hundred bookcases. From all that experience, we’ve learned that the best building tricks are shortcuts that avoid complex steps. So whether you’re a beginning builder or a veteran, these bookcase and shelf building tips will lead to beautiful results with less time and effort. Get the bookcase and shelf tips.
I don't like to be ignored either. I came the same day Mahndo left after waiting 30-45 mins. I left a note with name and number but no one even called me back. I was completely ignored. I found a class over at The Corona Heritage Park in Corona instead. Their instructor answers when I call or text. Nice to be acknowledged! Going to finish beginning and take advantage of the key access in their intermediate class.
In ancient times, the woodworker’s bench consisted of a plank or split log with four splayed legs. Descendants of those benches are manufactured today, usually with a top of hardwood slabs glued together. The norm nowadays is four straight legs supporting the bulk above, often with braces and a shelf below. Despite the improvements, the linkage to Greek and Roman antecedents is still evident.
These things may be tiny in size, but building one is not that easy. It takes some serious woodworking knowledge and skill to build a nice wooden mobile stand. When I first saw one online, I just couldn’t resist thinking of buying one. But when I saw the price, I was forced to rethink. Also, a woodwork lover like me cannot be contained with just one piece and I was not willing to spend on more than one. So instead I decided to build myself one. Yes, it took some doing but the final result was satisfying. Luckily, I found this awesome tutorial online that helped me build my first ever wooden phone holder.

I made a low table out of a couple of step-stools, my hollow-core door, and one of the MDF panels that would eventually form part of my top. I was concerned that any oil that dripped on the door might interfere with its glue adhesion, when I finally get around to the project for which I'd purchased it. The top side of the top sheet of MDF, though, I planned to oil, anyway. (Ditto for the bottom side of the bottom sheet.
A woodworker's Workbench is a special type of bench designed to hold your work when you are working on a wood project. The main purpose of this table is to keep the woodwork steady and to prevent it from moving. Follow the tutorial below to build yourself a nice workbench suitable for your specific woodworking projects. Make sure to modify the table to fit your specific requirements.
I'd decided on an oil-and-wax finish. Oil finishes are by no means the toughest. In fact, they're really rather pathetic, so far as protecting the wood goes. But they're easy to apply, and not even the toughest finish will stand up to the abuse that a workbench will suffer, so it's more important that it be easy to repair. Wax is usually used to add a high gloss. On a bench, it's there to keep glue from sticking.
Windsor Design is an interesting brand in that it is not actually its own company. Instead, Windsor Design is one of the in-house brands sold by Harbor Freight. While it may be a store brand, that should not dissuade you at all as Harbor Freight is known for selling some of the best products available for all fields of construction. Granted, this may not strictly be the best table available, but it does provide a solid mix of features to make it a good value.

Still in the building mood? Get free woodworking plans to build greenhouses, barns, pergolas, garages, dog houses, potting benches, router tables, playhouses, cabins, tree houses, gazebos, porch swings, picnic tables, swing sets, deer stands, bookcases, home bars, wine racks, decks, work benches, chicken coops, bird houses, benches, and even homes.

This table top is also made from the hardest wood out of any manufacturer we reviewed: oak. In fairness, this can be both a blessing and a curse. The oak wood is extremely durable and noted for its lack of a porous nature. This means the top can withstand plenty of abuse from tool and workpieces. Moreover, you will not have to worry about liquids like lacquers and stains from being absorbed into the top. That said, the hard oak can also do a number on tool sharpness, dulling them prematurely if they are not carefully handled.


The Classic Workbench is constructed entirely with in-compression-for-eternity drawbored mortise and tenons. It's as solid as humans can make it, short of growing a tree in the shape of a bench. The bench arrives at your shop completely assembled and ready to use. It doesn't knock down. The bench is built to the highest standards of traditional German craftsmanship in the utopian village of Amana Iowa. Our collaboration with the craftsmen in Amana, along with our experience in traditional workholding has yielded a workbench that is truly heirloom quality, but offered at what we think is a very reasonable price. We consider our flagship Split-Top Roubo as nearing the pinnacle of bench design (if there is such a thing) but we wanted to offer an essential bench built to high standards--an approachable but bulletproof tool for passionate enthusiasts of all levels, but especially intended for those just getting into the craft. Our principal bench maker has been steeped in the craft at the Amana Furniture Shop for nearly 50 years. Needless to say, a century and a half of woodworking tradition in Amana directly back to 19th century Germany speaks for itself. Many of the Amana craftsmen are multi-generational woodworkers.
We are especially proud of Post Woodworking’s Brunswick style shed. It has all the rugged features and simple, beautiful mystique of a Maine coastline. Natural-wood siding options, in pine or cedar, offer a rustic aesthetic. Or, choose a vinyl color that complements our home. Once inside the Brunswick, its unique, two-sided sloped roof maximizes headroom, making space for you to better maneuver a rake. Black architectural hinges and hardware lend distinguished contrast and quality to this basic but appealing storage solution.
×