I used the factory edge of the half-panel of hardboard as a guide for cutting the ply. I wanted to cut a 5-1/2" strip, and my saw cuts 4-1/2" from the edge of the shoe, so I wanted the edge of the hardboard 10" from the edge of the ply. So I set my combination square to 10", and used it to mechanically set the distance. Hint - if you need two things to be precisely the same length, try to avoid measuring them separately. Use some mechanical mechanism for setting the distance.
Turning an old door into a photo frame is another easy woodwork project. All you need is an old door and some woodworking tools and items. I am here sharing the link to the source tutorial that explains the step by step procedure for building a picture frame from an old wooden door. This tutorial was originally written by Tracy Snyder at athomewithsweett.blogspot.com who also tells you what items you may need and where to find them. If you haven’t already got an old door, you can purchase one from websites like Craigslist.
Synopsis: No room in the garage? Basement not an option? Consider what Ken St. Onge did when he needed shop space: He bought a prefabricated shed and converted it into his full-time woodshop. Because a pre-built shed doesn’t need a cement foundation and is built in a factory, it’s much less expensive than building an addition or stand-alone shop on your property. It can have taller ceilings than a garage and bigger doors than a basement, both big pluses for a woodworker. You can put a shed just about anywhere, too. Here’s a soup to nuts look at Ken’s experience, so you can gauge whether a shop in a shed is right for you.
Linseed oil sitting in a bowl, or spread on the surface of wood, is perfectly safe. But a linseed oil soaked rag provides a vastly increase surface area, so the oxidation happens faster, and the rag can provide insulation, trapping the heat. The increased temperature speeds up the oxidation even more, which raises the temperature even more, and the runaway feedback can quickly result in temperatures that will cause the rag to spontaneously burst into flame. This isn't one of those "do not drive car while sunscreen is in place" warnings. This is one of those "keep your finger off the trigger until you have the gun pointed at something you want to shoot" warnings. Rags soaked in linseed oil will catch fire, if you don't handle them properly, and they can do so far more quickly than you might think.

While a strict figure for the bench’s weight capacity is not available, a quick browse through their other stand and bench products shows a general weight capacity well above most other brands. As such, while we cannot say for certain that this bench provides the best weight capacity, it is more than likely that it the capacity is similar to the other products in the catalog.


I drilled from the mark. That way I could ensure that the hole was where it was supposed to be, on the side where the position was critical. I have two 3/8" bits -- a brad point bit that came with my doweling set, and a perfectly ordinary 3/8" twist bit. Brad-point bits are far more precise than twist bits -- they're more likely to start where you want them to, and they're more likely to stay straight. My problem is that my brad-point bit wasn't long enough to go through 3-1/2" of wood. So I started each hole with the brad-point bit, then finished it off with the twist bit. I clamped a piece of ply on the back, to reduce tear-out.

Raphael Berrios is one of our Foundations of Woodworking scholarship students in Spring 2016. He also took our Timber Frame Tiny Home course and brought home one of the structures to finish for himself (you can follow his progress on his blog!  Here’s what he had to say about what led him to PTSW, his experience so far, and thoughts for the future:
Great advice. May I add #11?…if you’re left handed (like me), build a left handed bench. It sounds obvious, but when I made my bench, I had looked at all the pictures in my books, laid out plans for a nice, traditional bench, built it, then realized my front vise should have been on the other end (I have no tail vise). I plane from left to right, and the front vise is always in the way.
After you have all the holes clean, set things up for your glue-up. You want everything on-hand before you start - drill, driver bit, glue, roller or whatever you're going to spread the glue with, and four clamps for the corners. You'll need a flat surface to do the glue-up on - I used my hollow core door on top my bench base - and another somewhat-flat surface to put the other panel on. My folding table was still holding my oak countertop, which makes a great flat surface, but I want to make sure I didn't drip glue on it so I covered it with some painters plastic that was left over from the last bedroom we painted.

Save money by selecting the right woodworking tools you need to purchase. You will have an excellent understanding of what tools, equipment and workshop features you need to get started in woodworking. By purchasing only the right woodworking tools and equipment you need, you will save money, allowing you to invest in higher quality tools and woodworking machinery.
This is another example of small woodwork projects that require good time and woodworking skills. This item is built using multiple wooden parts. Each part is shaped in a specific design and then all parts are attached together to make the final TV set. I have never tried building this one, mostly because I don’t own an iPhone, but also because making this item is not an easy task. By the way, it works fine with all kinds of phones.

We're planning to have a tree cutting service come in and take out a couple of diseased trees in the back part of our lot and then hire someone else to dig out the stumps. These trees are at the base of a small rise, and we're thinking about cutting into the "hill" a little bit and making a low retaining wall, maybe 18" to 24" high. But that's just intended to move the shed back a bit from the house. (Our total lot size is only 5,616 feet with an 1,800 square foot house.) Landscaping change like this won't affect current drainage patters, but anything else might make it worse.
I thought my first wood working bench was great.A heavy c channel metal frame with a recycled maple floor top with a guick release 7 in vice on the side.It is about 40in by 54in and can hold a hemi no problem. I waxed the top till it was nice and resistant to whatever was dripped on it. Only problem is I was thinking like a gear head not a wood worked.Work piece would slide and no decent clamping on the sides. I figured if I wanted to get somewhat serious about this woodworking thing I needed a real bench not a table with a vice. I read the books and with so many choices I chose a Roubo split top from Benchcrafted it would let me use it for both power and hand tools. I just finished it a week ago and it is nice not to have to chase my work across the bench. I couldn’t find a clear answer for a top coat for the bench I chose to leave the soft maple nude. So I guess I have a bench tbat has a lack of modesty.
The best thing about this wine rack is that it is very easy to build. All you need is the basic understanding of woodworking and a few tools to get started. You can modify your wine rack any way you want or build in a design or color different from this one. The basic steps to build a wooden wine rack are the same for all variants. I have included here the video tutorial that I followed in order to build myself a pallet wide rack.

Still, one of the best features about this woodworking bench has to be its vices. First off, the Sjobergs provides two vices both as sturdily constructed as the bench itself. The same hardware that fastens the bench works to ensure the vices are just as strong. The next main benefit on the vices in the inclusion of multiple positions – four in total – for the vices to go. This allows you to mix and match to suit your needs and allows the table to be used just as easily by right-handed and left-handed users.
Thinking about transitioning into serious woodworking, but don't have half a year or more to spare? Our one-month fine woodworking courses are perfect for those who are looking to move towards professional woodwork, but can’t find the time to commit to a longer course. Here, our woodworking classes will intricately teach you all of the basics, the same as you would for our three, six and twelve-month courses, with projects specially-created for both beginners and the more experienced. This will truly bring your woodworking skills up to the high level of craftsmanship needed within the industry.

This rack can be built from old unused wood pallets you can find around the house. So it is also a great way to recycle those old pallets. You can also find a step by step tutorial at instructables.com for which I have included the source link below. This tutorial helps you to make a wood wine rack from the scratch. So what are waiting for? Just grab the items you need and start building a cool wooden rack for those nice wine bottles of yours.
My name is Takami Kawai and I'm a traditional Japanese carpenter and architect with over 16 years of experience in sustainable design and construction. As much as conditions allow, I enjoy using traditional Japanese techniques. My experience includes working for the world renown, Ise Jingu Grand Shrine. I have also hosted numerous presentations on traditional Japanese woodworking. Now, I run a small construction firm, Suikoushya, which specializes in the restoration of traditional Japanese houses.
The Classic Workbench is based largely on the famous Plate 11 workbench from Roubo’s “The Art of the Joinery”. We’ve built dozens of these “Roubo” benches over the past decade, helped others build hundreds more and examined extant French benches from the period. We haven’t changed our opinion on this fundamental design. French technical schools of the late 19th and early 20th centuries were outfitted with benches of the exact type. And prior to the 1950’s, you could easily buy a “Classic” workbench from any number of French supply houses. Benchcrafted continues the tradition by offering this excellent workbench, built in Iowa with American hardwoods to the highest standards.
The projects in this course follow a natural progression of skills, techniques and tools. Some of the early student-made tools are, in fact, used to help make the next tool or bench fixture in the series. You are supported in the building of these projects with step-by-step outlines, knock-down examples and continuing, one-on-one consultations with the faculty. Periodic evaluations of your progress with a specific faculty-mentor help keep you on track.
The holes we want to mark are the holes through which the threaded rod connecting the two legs will run. This threaded rod will run through the 3/8" groove along the bottom of the short stretchers,. The hole for the upper stretcher has to be positioned so that when the rod is running through this groove, the top of the short stretcher is even with the top of the legs. The most precise way I've found for marking the position of this hole is to use a dowel center. Fit the dowel center into the bottom groove, line up the stretcher, and bang on the end with a rubber mallet. The dowel center will leave a mark indicating the center of the hole.

I never, ever, ever bother to write these things. But, I am so incredibly impressed with this product, that I feel compelled to. My six year old daughter LOVES IT, as does my almost four year old daughter. The hammer is just the right size, and it comes with enough pre-cut (good quality) wood for many projects. So far, they have made a house, car, and a plane-- all of which are far more aesthetically pleasing (to me, as a mom) than the plethora of junky plastic toys that seem to fill our home. We've used these projects both as math lessons (measuring the wood, counting the nails needed, learning about angles, reviewing shapes) and during arts & crafts time; but, with just a little creativity, they could be incorporated into just about any learning subject. For the amount of enjoyment we have received, thus far, this product is already worth the money spent, and we have several more projects to go! We will be buying another for little sister's upcoming birthday, most definitely.

The jaw for the front vise needed to be 10" long - to span the distance from the leg to the end of the top, 1-1/2" thick - to allow for benchdog holes to be drilled in it, and 5" tall. The end vise was mounted 3/4" lower than the front vise, and the screw and guide rods were thicker, so its jaws needed to be at least 6-1/2" tall. Again, they needed to be 1-1/2" thick to allow for benchdog holes, and 23" long to span the width of the bench.
Flip the base upright, put the MDF on top of it, then use a straightedge to draw two straight lines joining the outside edges of the legs and extending the width of the MDF. I used the countertop as the straightedge. We cut it with our cutting guide, which is based on the factory edge of a sheet of 1/4" plywood, so it should be straight enough. Use a carpenter's square to transfer these lines onto the ends of the MDF.
One quality about this bench that is definitely lacking is space – both tabletop and storage. The Olympia Tools does provide an adequate shelf, but it does not come with any drawers, nor does it offer the option of adding them later. The table top is the smallest we saw at 50” long and 2’ wide, though the width is actually better than most of the other table we reviewed. Still, a significant chunk of that width is occupied by a trough. This trough is designed to hold smaller workpieces to keep them from falling or getting knocked over, but it removes about 6” of width from the tabletop.
The video explains the step by step process of making a nice wooden phone stand from scratch. My first wooden holder was not the best one, but it was good enough to motivate me to make more. I now possess 10 mobile wooden stands in different shapes and styles. And if I can make this, you too can make one yourself. Search the internet for more mobile holder ideas and start making one now.
Workbenches have flat tops, though sometimes at the rear there is a cavity called a tool well that contains tools and components (and prevents them from falling off). One advantage of having the well set into the top of the bench is that, even with a variety of objects in the well, a large sheet of material can still be laid flat over the entire surface of the bench; the contents of the tool well offer no interference.
Some tools required for this project are hole saw, drilling machine, pencil, tape measure, clamps, etc. This tutorial explains every step properly with images so that anyone can make a wooden sofa sleeve easily. Those, who prefer a video tutorial, can visit the below link to a YouTube video that illustrates the process of building a DIY Sofa Sleeve Cupholder.
TOH has showed you how to make a toy chest with your kids before, but if you don't feel like cutting the wood yourself, opt for a kit like the one for this beautiful cherry chest. The kit comes with pre-cut pieces and all the hardware you need. Like many toy chests out there, the closed lid can also function as a bench seat, and the hinges are designed to prevent little fingers from getting caught. This model is available in three different finishes.
I thought my first wood working bench was great.A heavy c channel metal frame with a recycled maple floor top with a guick release 7 in vice on the side.It is about 40in by 54in and can hold a hemi no problem. I waxed the top till it was nice and resistant to whatever was dripped on it. Only problem is I was thinking like a gear head not a wood worked.Work piece would slide and no decent clamping on the sides. I figured if I wanted to get somewhat serious about this woodworking thing I needed a real bench not a table with a vice. I read the books and with so many choices I chose a Roubo split top from Benchcrafted it would let me use it for both power and hand tools. I just finished it a week ago and it is nice not to have to chase my work across the bench. I couldn’t find a clear answer for a top coat for the bench I chose to leave the soft maple nude. So I guess I have a bench tbat has a lack of modesty.
Still in the building mood? Get free woodworking plans to build greenhouses, barns, pergolas, garages, dog houses, potting benches, router tables, playhouses, cabins, tree houses, gazebos, porch swings, picnic tables, swing sets, deer stands, bookcases, home bars, wine racks, decks, work benches, chicken coops, bird houses, benches, and even homes.

All-in-all, the Windsor Design workbench is a nice companion, especially if your budget is limited. It is not as deeply designed and perfected as the other two benches, as there is only one vice, the bench dog holes are drilled through the surface (allowing debris to fall to the top drawers) and the drawers can be a little flimsy if you are not using glue for assembling it, but for the price they offer, there are plenty of perks.
Whether you're just starting out or wish to upgrade your important hand tools, this 5-Pc. Professional Woodworking Kit with matching rosewood and brass accents has all the essentials for producing the very best work. This fine set includes a 9" smoothing plane, 6" block plane, 9" try square, 9" marking gauge, 9" bevel gauge and a fitted wooden case.
There are a number of tricks to using a router. First, the bit spins in a clockwise direction, as you look down at the router from the top. This means that when you cut with the router from left to right, the bit will tend to pull the router away from you, and when you route from right to left, the router will pull towards you. So, if you're hooking the edge guide along the near side of the board, route from left to right, and when you're hooking it along the far side of the board, route from right to left. Second, always test the position of your bit on scrap material. Your odds of getting it exactly right by eye are nil. Third, don't cut more than 1/4" deep on a single pass. We want a 3/8" deep grove, so make your first pass at 3/16", or thereabouts, and make a second pass to reach the full depth.
ALL Red Kits require planing and jointing of wood. Red Kits require the skill and tools to cut and make joints including panels. The woodworker needs to be able to cut, join, assemble and finish. Red Kits require the woodworker to be able to read the plans and to transfer images and dimensions from the plan to the lumber. It supplies all of the needed hand-selected, dimensioned lumber but woodworking knowledge and tools are recommended to be successful with Red Kits.
It doesn't get much better than a day at the woodshop! I've taken several classes from cutting boards to turning vases. It is always fun and informative! All of the machines are top notch and the instructors are great! I've toyed with the idea of a membership but I think I'll take a couple more classes before doing so! I can't wait to see the new location! :)

The hacksaw will often damage the last thread when it cuts. Running a nut off the end will fix this. You'll have to run the nut all the way down from the other end. This doesn't take long, if you chuck up the rod in your drill and let it do the work. Hold the rod vertically, with the drill pointing down, and just hold on to the nut enough to keep it from spinning.
Cut 15 top boards 5 ft. long and rip them to 3 in. wide with a table saw so the top will glue up flat without the typical rounded edges of 2x4s. For the leg slot, cut two of the top boards into three pieces: a 39-in. middle piece and two 7-in. end pieces. Glue and screw the top together, one board at a time, with 3-in. deck screws, keeping the ripped edge facing up and level with the adjoining boards. Use a corded drill so there’s plenty of oomph to drive each screw below the surface. Note that the third glue-up from each end is where each leg notch is inserted. You can also create a nifty tool tray in the top by notching the three top pieces with a jigsaw. Clamp every 8 in. or so before driving in the 3-in.deck screws. Predrill the screw holes near the ends to prevent splitting. When you’re screwing on the 7-in. long 2x4s to create the leg slots, use a scrap piece of 2×4 as a spacer.
If you don't quite have the space for a real pony, make this handcrafted wood version instead. The horse pictured here is unfinished pine, but there are lots of woods and finishes to choose from. Everything you need comes with the kit, and the plans can be downloaded. If you don't want to build it yourself, you can order from the website—just allow two to three weeks to ship.
This is not exactly a tutorial, but a guide to some really cool woodworking projects. Although we are not teaching you to make anything, we are always here to help. Feel free to ask your queries in the comments in case if you face any issue while working on any of these projects. Also, tell us how much you liked this article. Did you enjoy reading it? Did you work on any of these projects, and if yes, how was your experience? You are also welcome to share any images of your completed woodwork projects.
For most of the course, we'll be heavily focused on developing your skills using hand tools. As a developing woodworker, there is no substitute for putting in the hours of direct hands on practice it takes to gain an intuitive understanding of wood. The early part of this course focuses on working with hand tools as we believe they bring you closer to wood as a material.  You can rip a board on a table saw with out much thought to the wood itself, but you will understand much more about grain if you rip a board with a hand saw.  As the course progresses, machine processes are introduced as a pragmatic aid in expediting projects.  
This particular tray is made using reclaimed barn wood but the author of the project Beyond The Picket Fence surprised everyone with one fact: reclaimed barn wood has often some areas turned pink due to cow urine. If you check the project more closely, you’ll also notice some areas of the tray being almost bright pink. That’s something you don’t see every day!
For most of the course, we'll be heavily focused on developing your skills using hand tools. As a developing woodworker, there is no substitute for putting in the hours of direct hands on practice it takes to gain an intuitive understanding of wood. The early part of this course focuses on working with hand tools as we believe they bring you closer to wood as a material.  You can rip a board on a table saw with out much thought to the wood itself, but you will understand much more about grain if you rip a board with a hand saw.  As the course progresses, machine processes are introduced as a pragmatic aid in expediting projects.  
We offer Arrow, Best Barns, EZ-Fit and Handy Home Products brands wood and wood like storage sheds. If you're looking for a premium all wood storage shed kit, All Pre-Cut Best Barns sheds, EZ-Fit sheds and Handy Home Products sheds are excellent choices! All Pre-Cut Best Barns sheds, All EZ-Fit and All Handy Home shed kits come with everything pre-cut and ready for assembly. Every wood shed kit comes with easy to follow do-it-yourself instructions to help you build a one of a kind beautiful outdoor storage area. Similar to the All Pre-Cut line from Best Barns we also offer the basic model labelled Best Barns which is also made by Reynolds Buildings Inc. Our Best Barns line of wood sheds is very similar to the All Pre-Cut sheds except they need a couple extra hours of work and can save you a few hundred extra dollars! Best Barns not labelled All Pre-Cut will require straight cuts to complete the roof and siding. For an even more cost effective wood shed look we've also included some of our metal, wood like sheds from Arrow sheds for someone just wanting the look of wood with a lower price tag. Buy your new wood shed today and get that storage problem solved! For helpful information and answers to frequently asked questions about our buildings read helpful articles about our sheds.
The bench would end up being about 5 feet long. I thought about cutting 5 feet out of my 8 feet long countertop and use the rest for a small support table. However, after a consideration, I decided to bypass the front vise altogether together with the overhang so my bench will be 4 feet long. This allows me to skip the MDF and just glue the two halves of the 8 feet board together.
With the inner jaw fastened to the bench, I used the router to flush-trim the jaw to the benchtop, across the top and down the sides adjacent to the top (stopping short of the discontinuity between the top and the legs). I'd thought this would be the best way to match up the jaw against the top, but I'd not do it this way again. It was very difficult to hold the router tight against the face of the jaw, and the result was a surface that wasn't as even as I had hoped.

MechanicGuides.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for website owners to earn advertising fees by advertising and linking to amazon(.com, .co.uk, .ca etc) and any other website that may be affiliated with Amazon Service LLC Associates Program. Amazon and the Amazon logo are trademarks of Amazon.com, Inc. or its affiliates.


For the router you'll need a a 3/8" straight bit, an edge guide, 1/4"- and 1/8"-radius roundover bits, and a flush-trim bit with at least a 1-1/2" cutting length. Bits of this size are available only for a 1/2" collet. Some routers are capable of using multiple collet sizes. I was fool enough to buy a router that only had a 1/4" collet. More on that, later.
I don't see anywhere you mentioned the over all length of the bench top. A piece of 1 1/2" x 25" x 8' glued edge oak at Lumber Liquidators costs $192 including tax. Two piece is almost $400! Would that be better if I use two IKEA 1 1/4" x 25" x 74" solid Beech ($99 each plus tax) on top of a layer of 3/4" Birch plywood. That would be 3 1/4" over all.
Making an art or a design on a wooden piece is a hectic task and requires good art skills. But there is another much easier way to carve a beautiful art on any wood surface. For this, you will need the image or graphic that you want to transfer, a piece of wood, freezer paper, etc. I, myself have made several such designs. At the source below, you can find a step by step guide for transferring a graphic image to the wood.
Require the woodworker to be able to read the plans and to transfer images and dimensions from the plan to the lumber. The wood has been planed and all glued panels are completed unless over 14 inches. If panel required is over 14 inches, one glue seam will be required. The woodworker needs to be able to do some cutting, jointing, assembling and finishing. White Kits do not require planing. White Kits supply all of the needed hand-selected dimensioned lumber, but woodworking knowledge and tools will be useful to complete the project successfully.
With my second attempt at edge guides, I made the other rough-cut. On this, the edge guide worked fine, but the end of the cuts revealed that the saw blade wasn't quite square. So I adjusted the blade, clamped all four legs together, and made what would be the first final cut, if it came out clean enough. It didn't. I'd let the saw drift a bit away from the guide edge. So I adjusted the saw, moving the guide back half an inch, and tried again. the rough-cut parts were a couple of inches longer than they needed to be, so I had room to work with,. It's only the final cut at the other end that you only have one chance at.
I ended up making a number of practice cuts. The first revealed that I hadn't tightened the screws on the edge guide enough. The second revealed that the design of the edge guide provided very little support at the end of a board, because of the cut-out for the router bit. In the "Getting Started in Woodworking" video, they had screwed a piece of hardwood to the edge-guide, to provide a continuous -- and longer -- bearing surface. I may do that myself, some day, but I didn't have the materials at hand, so I clamped some 2x4 scrap to the end of each board, to provide a continuous bearing surface past the ends. The two grooves in the long stretchers and the side groove in the short stretchers have identical layout. I made practice cuts in scrap until I had the edge guide set correctly, then I cut them all with that one setting. The bottom groove of the short stretchers uses a different setup, so it was back to the scrap, before cutting them.

Students in the beginning woodworking class learn how to use a variety of tools, including a band, miter and table saw, a drill press, a jointer and a planer. Through the lathe technology class, students become familiar with a number of cutting, scraping and finishing techniques. Successful completion of the course leads to a lathe certification for the wood shop.


1. In this post, you kindly remind us not to make it too deep or worry too much about the height. I presume you still believe a bench cannot be too long or too heavy? I’m with you — just asking if that’s actually still your opinion, since the bench above appears to be yet another six footer. (If longer is better, why don’t you build an 8 or 10′ for your home shop?) TYIA – remember, I’ve bought all my lumber to start my new bench, but I haven’t milled anything yet, so you’re really helping in an immediate way here!
The Community Woodshop allows me to have access to a countless number of the best quality tools in the industry. They are always on top of keeping everything working and running.  If anything breaks they are always very proactive in fixing things ASAP.  They also have more than enough tools so I never have to wait to use a sander or any of the smaller tools, and I have never had to wait more than a few minutes to get on the table saw (and even that is rare).

A steam box and a heat source are the two main components used to steam bend wood. Steam boxes must be able to withstand large fluctuations in temperature and humidity without breaking apart. In this two-hour workshop, students will build an optimized steam box that can last through the tough job of steaming wood, allowing them to continue creating their own projects at home!

Having done all this, I'm not sure I'd do it this way again. It might well be faster to layout the positions with compass and straightedge directly onto the top. Either way, you'll want to use a scribe rather than a pencil. Scribe lines are hard to see, and impossible to photograph, but the scribe and compass points click into them, allowing a precision that pencils simply cannot match.
I was a short-term member at Community Woodshop, but it's left a lasting impression on me! They have everything you need to build a variety of projects, and i definitely got some good use out of their quality equipment. The staff is very knowledgeable and friendly, and are always around to offer sound advice and to make sure you have a safe setup. I only discontinued my membership due
A woodworker's workbench isn't a table, it's a work-holding system. It's not something you set things on top of, it's a tool that holds your work. Where a worktable might have a machinist's vise bolted to its top, a woodworker's bench is built to accommodate a number of different workholding mechanisms, such as bench dogs, planing stops, hold fasts, or board jacks, and will usually have one more woodworker's vises integrated into its structure.
Had a great experience at the shop! My schedule is hectic and unfortunately can't make the classes, but I did do a private lesson with Bob.  In one afternoon, we created two cutting boards.  Bob was very detailed with breaking down the process and using the machines.  Honestly didn't expect to make two cutting boards but Bob was proficient with time.  I got really comfortable using the machines especially the table saw.  I learned how to use the planer, jointer, miter saw, table saw, drill press, router, disk sander, and random orbital sander.  Really recommend folks that are interested in woodworking with little to no experience to take the Safety Orientation and the Cutting Board class or private lessons.  Looking forward to my next project at the shop!
I agree that I might quickly outgrow a 12x8 shed. Lowes also offers a 12x10 Rancher (same style, but more room), but the 12x10 is 9 feet, 4 inches high, and my community only allows a maximum height of 9 feet. The 12x8 is exactly 9 feet high. I'm afraid of getting "out of spec" if I exceed the height limit and then getting in trouble with the Home Owner's Association. Having said that, 12x10 would be about the biggest size I could get for the available area in my back yard, so even if I hire a shed contractor to do this, the shed would have to be 12x10 or smaller.
×