Through demonstrations and practice you will learn how to build a Simple Table Top. Square wood using the Jointer, Planer and Table Saw, then learn how to use the Festool Domino Joiner to keep perfect registration during the glue up. This will be a group project where everyone will help build a single table top. The goal is to gain experience and confidence...
At Costco, we understand that when you’re looking for a shed or barn, you’re not just looking for a space to store your tools, you’re looking for a structure that’s reliable, sturdy, and weatherproof. This kind of quality assurance is especially important when your shed or barn isn’t just a toolshed, but a place for storing your memories or working on projects. At Costco.com, you’ll find sheds and barns of all shapes, sizes, and materials. Shop by brand, color, or features, and rest assured, knowing that whatever structure you choose, you’re getting it at the best possible price!
The Handy Home Products Berkley 10 ft. x The Handy Home Products Berkley 10 ft. x 16 ft. Do-It-Yourself Wood Shed Kit Combines charming country style and outstanding performance for the ultimate powerhouse. Offering maximum storage this woodshed is the ideal solution to house all your outdoor tools and lawn gear. Featuring 2x4 wood framing it boasts a ... More + Product Details Close
Cut 15 top boards 5 ft. long and rip them to 3 in. wide with a table saw so the top will glue up flat without the typical rounded edges of 2x4s. For the leg slot, cut two of the top boards into three pieces: a 39-in. middle piece and two 7-in. end pieces. Glue and screw the top together, one board at a time, with 3-in. deck screws, keeping the ripped edge facing up and level with the adjoining boards. Use a corded drill so there’s plenty of oomph to drive each screw below the surface. Note that the third glue-up from each end is where each leg notch is inserted. You can also create a nifty tool tray in the top by notching the three top pieces with a jigsaw. Clamp every 8 in. or so before driving in the 3-in.deck screws. Predrill the screw holes near the ends to prevent splitting. When you’re screwing on the 7-in. long 2x4s to create the leg slots, use a scrap piece of 2×4 as a spacer.
Regardless of which type of screw you use, you'll need to flip the panel and use a countersink drill to on all of the exit holes. Drilling MDF leaves bumps, the countersink bit will remove them, and will create a little bit of space for material drawn up by the screw from the second sheet of MDF. You want to remove anything that might keep the two panels from mating up flat. I set a block plane to a very shallow bite and ran it over what was left of the bumps and over the edges. The edges of MDF can be bulged by by sawing or just by handling, and you want to knock that down.
Once you start spreading glue, you have maybe five minutes to get the two panels mated, aligned, and clamped together. So make sure you have everything on-hand, and you're not gong to be interrupted. Start squeezing out the glue on one MDF panel, and spreading it around in a thin, even coating, making sure you leave no bare areas. Then do the same to the other MDF panel. Then pick up the bottom panel and flip it over onto the upper panel. Slide it around some to make sure the glue is spread evenly, then line up one corner and drive in a screw. Line up the opposite corner and drive in a screw there. Clamp all four corners to your flat surface, then start driving the rest of the screws, in a spiral pattern from the center.
With the Grain: A Craftsman’s Guide to Understanding Wood by Christian Becksvoort. A little knowledge about trees goes a long way toward improving your woodworking. You don’t need a degree in dendrology to build a desk. But you do need intimate knowledge of how our raw material grows and – more importantly – how it responds to its environment after it has been cut and dried.
For a fun and comprehensive learning experience, take an online woodworking class in the WWGOA Academy. You’ll learn in-depth woodworking how-to, get bonus material, and enjoy custom benefits for class participants. You’ll never lose access to your Class; no strings attached! Check back often – as we’re adding new online woodworking classes regularly.
The bench would end up being about 5 feet long. I thought about cutting 5 feet out of my 8 feet long countertop and use the rest for a small support table. However, after a consideration, I decided to bypass the front vise altogether together with the overhang so my bench will be 4 feet long. This allows me to skip the MDF and just glue the two halves of the 8 feet board together.
I agree that I might quickly outgrow a 12x8 shed. Lowes also offers a 12x10 Rancher (same style, but more room), but the 12x10 is 9 feet, 4 inches high, and my community only allows a maximum height of 9 feet. The 12x8 is exactly 9 feet high. I'm afraid of getting "out of spec" if I exceed the height limit and then getting in trouble with the Home Owner's Association. Having said that, 12x10 would be about the biggest size I could get for the available area in my back yard, so even if I hire a shed contractor to do this, the shed would have to be 12x10 or smaller.