The next day, cut it flush. Use a block plane to ensure it truly is flush. This will be the top of the bottom layer of the bench top, so gouges aren't a problem. (Wiping up glue with a damp cloth can lead to stains and finishes applying unevenly. That won't be a problem here, either.) But bulges and bumps are a problem - they will keep the two layers of the top from matching up evenly.
The bench would end up being about 5 feet long. I thought about cutting 5 feet out of my 8 feet long countertop and use the rest for a small support table. However, after a consideration, I decided to bypass the front vise altogether together with the overhang so my bench will be 4 feet long. This allows me to skip the MDF and just glue the two halves of the 8 feet board together.
Regardless of which type of screw you use, you'll need to flip the panel and use a countersink drill to on all of the exit holes. Drilling MDF leaves bumps, the countersink bit will remove them, and will create a little bit of space for material drawn up by the screw from the second sheet of MDF. You want to remove anything that might keep the two panels from mating up flat. I set a block plane to a very shallow bite and ran it over what was left of the bumps and over the edges. The edges of MDF can be bulged by by sawing or just by handling, and you want to knock that down.

This is for the serious amongst you. Those of you who are ready to make a change in your life. To really surround themselves with woodworkers and furniture making for a whole year. Not only do you get to learn some great traditional skills but also drawing, the beginnings of design and how to run a woodworking business successfully. This intense workshop training gives you a good foundation to make your own way to become a furniture maker.
Our stationary equipment runs the complete range from heavy-duty industrial machines, to inexpensive home shop type of tooling so that each student can compare and contrast the range and versatility of equipment at a wide variety of price points.  We spend time on what makes a good machine good, an adequate one adequate, and a lousy machine worthless. We have no commercial sponsors and will share our opinions based on our experiences regarding the quality of one manufacturer over another.  There is no better place to kick the tires on a variety of equipment than at our shop.     
Frame making may look simple but it is a skill that escapes many. For a frame to properly do its job it has to be perfect, any mistake can be a distraction that takes away from the artwork it surrounds. This class will focus on skills essential to making square or rectangular frames. Skill building concepts will include how to break down and mill...
The holes we want to mark are the holes through which the threaded rod connecting the two legs will run. This threaded rod will run through the 3/8" groove along the bottom of the short stretchers,. The hole for the upper stretcher has to be positioned so that when the rod is running through this groove, the top of the short stretcher is even with the top of the legs. The most precise way I've found for marking the position of this hole is to use a dowel center. Fit the dowel center into the bottom groove, line up the stretcher, and bang on the end with a rubber mallet. The dowel center will leave a mark indicating the center of the hole.
Yea I had a friend who went the HD route and in after putting new braces up for the roof and an extra layer of plywood on the floor he gave up the fight and tore it down. We ended up building twice the shed that was 100 times more sturdy for less than he had invested in the first one. I would go any route that is the opposite way of HD or Lowes. Learn from this guy.
You are absolutely right on your advise. When I was agonizing over how to build a workbench my good friend turned me on to your book on workbenches. I was planning on having an overhang until I read your advise about building a workbench and not a table. So the entire front and rear surfaces; top, legs and bottom shelf are all in the same plane to clamp my work to. The addition of a sliding dead man was also something that I would have never thought of on my own. Thanks again for your advise.
Lay a leg flat on your work surface, with the countersink side of the thru-holes down. Stick a piece of threaded rod in each hole. Take a stretcher that is marked to have one end adjoin the top of this leg, stick a dowel center in its dowel hole, line it up against the leg, using the threaded rod for positioning, You want the top of the stretcher to be even with the top of the leg, or just slightly above it. Give the end of the stretcher a whack with your rubber mallet. This will leave a mark indicating where the matching dowel hole in the leg needs to be drilled. Repeat with the lower stretcher than adjoins this leg. Then repeat for the other leg that will form this trestle, and the other ends of the two stretchers.
First, we need to drill out the holes for the screws that will hold them together. While the two layers of MDF are glued, the countertop and the MDF will only be screwed. The oak countertop, like any natural wood product, will expand and contract with humidity changes. If it were glued to the MDF, the difference in expansion of the two layers would cause the countertop to buckle and curl.
Let me see if I can come up with a couple details. The table saw is a TS3660. So I have heard, this should be the center of your shop. My jointer is a 6 1/8" Jointer / Planer JP0610 which is 45 inches in length. My router table is the kreg router table that takes up a 24 x 32 inch footprint. My bench is roughly 30 x 70 inches and my bandsaw is 3' x3'. I have other tools as well such as a portable 12.5 Delta thickness planer in addition to a wall mounted dust collector. To add to the list, I am just about to get a 10 inch makita sliding compound miter saw. I can see how space will be eaten up quickly. Any ideas as to how arrange these tools in such a small shop? I will get pics a soon a I
Great advice. May I add #11?…if you’re left handed (like me), build a left handed bench. It sounds obvious, but when I made my bench, I had looked at all the pictures in my books, laid out plans for a nice, traditional bench, built it, then realized my front vise should have been on the other end (I have no tail vise). I plane from left to right, and the front vise is always in the way.

The Handy Home Products Berkley 10 ft. x The Handy Home Products Berkley 10 ft. x 10 ft. Wood Storage Building Kit with Floor is made with factory-primed SmartSide siding to resist fungal decay and wood-destroying insects. The Berkley’s gambrel style roof provides plenty of height to add a loft for extra storage space. The 6 ft. high ...  More + Product Details Close
Constructed with the classic craftsmanship that Grey’s Woodworks is known for, our beautiful sheds come in a variety of styles, sizes and colors. We will help you design a shed to match your surroundings and meet your needs. Select from our pine tongue and groove, duratemp T1-11, or vinyl sidings and arrange doors and windows to your liking. All of our sheds are handcrafted in modern workshops. Not only does a shed from Grey’s Woodworks provide much needed storage space for your mower, snow blower or bike, but it also makes for an attractive addition to your property.
In each Practical Woodworking Class, the daily mix consists of intensive lecture, demonstration, and student practice lab time.  Lecture periods are interactive, informative, and intensive but are also an enjoyable experience.  Generally, each joinery and fabrication process is demonstrated in several ways to reach or achieve the same results.  For example, processes are first demonstrated with the use of hand tools. Next, the same joint or procedure is done with simple hand held power tools (such as the router). Then, the entire process is demonstrated with stationary equipment such as the table saw, drill press, and mortiser. Students choose whichever production method works best for them and is in keeping with their plan to equip a home workshop and/or around their existing home tooling.
Still, one of the best features about this woodworking bench has to be its vices. First off, the Sjobergs provides two vices both as sturdily constructed as the bench itself. The same hardware that fastens the bench works to ensure the vices are just as strong. The next main benefit on the vices in the inclusion of multiple positions – four in total – for the vices to go. This allows you to mix and match to suit your needs and allows the table to be used just as easily by right-handed and left-handed users.
I agree that I might quickly outgrow a 12x8 shed. Lowes also offers a 12x10 Rancher (same style, but more room), but the 12x10 is 9 feet, 4 inches high, and my community only allows a maximum height of 9 feet. The 12x8 is exactly 9 feet high. I'm afraid of getting "out of spec" if I exceed the height limit and then getting in trouble with the Home Owner's Association. Having said that, 12x10 would be about the biggest size I could get for the available area in my back yard, so even if I hire a shed contractor to do this, the shed would have to be 12x10 or smaller.
×