I ended up making a number of practice cuts. The first revealed that I hadn't tightened the screws on the edge guide enough. The second revealed that the design of the edge guide provided very little support at the end of a board, because of the cut-out for the router bit. In the "Getting Started in Woodworking" video, they had screwed a piece of hardwood to the edge-guide, to provide a continuous -- and longer -- bearing surface. I may do that myself, some day, but I didn't have the materials at hand, so I clamped some 2x4 scrap to the end of each board, to provide a continuous bearing surface past the ends. The two grooves in the long stretchers and the side groove in the short stretchers have identical layout. I made practice cuts in scrap until I had the edge guide set correctly, then I cut them all with that one setting. The bottom groove of the short stretchers uses a different setup, so it was back to the scrap, before cutting them.
In general, students in the certificate and degree programs learn how to understand and create their own shop drawings and design custom cabinetry. In the process, they also find out how to use the same tools and machines employed in the woodworking business and assemble cabinets according to industry standards. Additional program topics include the use of contemporary hardware in design.
Cut 15 top boards 5 ft. long and rip them to 3 in. wide with a table saw so the top will glue up flat without the typical rounded edges of 2x4s. For the leg slot, cut two of the top boards into three pieces: a 39-in. middle piece and two 7-in. end pieces. Glue and screw the top together, one board at a time, with 3-in. deck screws, keeping the ripped edge facing up and level with the adjoining boards. Use a corded drill so there’s plenty of oomph to drive each screw below the surface. Note that the third glue-up from each end is where each leg notch is inserted. You can also create a nifty tool tray in the top by notching the three top pieces with a jigsaw. Clamp every 8 in. or so before driving in the 3-in.deck screws. Predrill the screw holes near the ends to prevent splitting. When you’re screwing on the 7-in. long 2x4s to create the leg slots, use a scrap piece of 2×4 as a spacer.
Through demonstrations and practice you will learn how to build a Simple Table Top. Square wood using the Jointer, Planer and Table Saw, then learn how to use the Festool Domino Joiner to keep perfect registration during the glue up. This will be a group project where everyone will help build a single table top. The goal is to gain experience and confidence...
Another odd design feature of the Windsor Design is its dog holes. While this bench provides a variety of dog holes and even offers numerous pegs and dowels to go along with it, the dog holes are not spaced as closely or with as much variation as you see with many other benches. Ultimately, this means that smaller workpieces may not be able to use the dog holes and pegs as well.
Once you have all the clamps on, take off the scraps of hardboard. You can clean up the glue squeezeout with a damp rag.. When the glue is dry, trim down the strip flush with the panel using a router and a flush-trim bit. Then cut off the ends of the strip with a flush-cut saw, and clean up with a block plane, an edge scraper, or a sanding block. Leaving the ends in place while you route the edge helps support the router.

I am sharing here a link to the detailed tutorial written by Pete at diypete.com, who shares the step by step process for making a wonderful barrel coffee table from scratch. He also tells you what items you’ll need for this project and where to find them. For example, you can buy an old whiskey barrel online or from a local whiskey store for a few bucks, if you haven’t already got one.
Place sounds amazing. Receptionist was rude. Sarcastic remarks were not necessary. I called regarding the private lessons. And was told that they "can't hold my hand to do the work". The person made the statement not allowing me to finish saying that I have experience with wood work. I was really upset by the statement. He did not seem interested in having me as a client/student.
My first attempt at making a cutting guide didn't work. What I ended up with worked fine for cutting panels, but the guide-strip was too narrow, and when the saw was extended fully for rough-cutting the 4x4's the clamp heads got in the way. So I made another. Actually, I made two more, so that I could cut one into shorter pieces that would be easier to handle.

Over the years, the editors at The Family Handyman have built nearly a hundred bookcases. From all that experience, we’ve learned that the best building tricks are shortcuts that avoid complex steps. So whether you’re a beginning builder or a veteran, these bookcase and shelf building tips will lead to beautiful results with less time and effort. Get the bookcase and shelf tips.


The book is well written and easy to read. The illustrations, I'm sure were excellent in 1914 and, are still adequite now. Most of the designs seemed repetitive, though. I wish more attention had been given to lashing materials. If you are looking for that you will find almost none here. The book was fun to read and provided enough inspiration to make my brother and me attempt a large hut.
×