The holes we want to mark are the holes through which the threaded rod connecting the two legs will run. This threaded rod will run through the 3/8" groove along the bottom of the short stretchers,. The hole for the upper stretcher has to be positioned so that when the rod is running through this groove, the top of the short stretcher is even with the top of the legs. The most precise way I've found for marking the position of this hole is to use a dowel center. Fit the dowel center into the bottom groove, line up the stretcher, and bang on the end with a rubber mallet. The dowel center will leave a mark indicating the center of the hole.
 I have always wanted to share this wonderful woodworking world with like-minded people from all over the world. For the last six months, I have started sharing Japanese woodworking information through videos and photos. Because of the huge amount of interest, I started organizing one-day workshops for people visiting Kyoto, letting them experience Japanese woodworking tools.
AJ and Scott have been very helpful showing me where tools are my first few days there. This is a workshop where you will have to work independently. They will show you how to use certain machines for the first time and orient you to the shop itself but they will not help you with your project.  They can, however, be hired to help you with projects if that's what you need. I believe it's $75 an hour and limited to their availability. There is also a host of classes you can take if you want an intro into cabinet making, wood joining, turning etc. There are a lot of different classes that may pique your interests.
A woodworker's workbench isn't a table, it's a work-holding system. It's not something you set things on top of, it's a tool that holds your work. Where a worktable might have a machinist's vise bolted to its top, a woodworker's bench is built to accommodate a number of different workholding mechanisms, such as bench dogs, planing stops, hold fasts, or board jacks, and will usually have one more woodworker's vises integrated into its structure.
These sorts of things are usually glued and screwed, but it's actually the glue that holds them together - the screws just hold everything tight while the glue cures. Screwing into hardboard or 1/4" ply is an exercise in futility, so I just used glue, and used my two 4x4's as long clamps. It would have been a bit easier, if I'd done this before I'd rough-cut the 4x4's, but it worked out.
I recently came across this beautiful wooden swing set, which was made in the shape of a boat. Cool, isn’t it? The very first look was enough for me to start loving it. Although I haven’t yet tried building one myself, I am definitely going to. Later I realized that you can also build a baby cradle with the same idea. After all, what can be more calming than the tender rocking of a boat? This swing set will surely help your child get more gentle sleep.
To mark the centerline, set a compass to span something more than half the width of the leg. Draw an arc from corner of the leg. The point where the arcs intersect will be on the centerline. With a centerline point on each end of the leg, place a scribe on the point, slide a straightedge up to touch the scribe. Do the same on the other end. When you have the straightedge positioned so that you can touch both points with the scribe, and in each case it is touching the straightedge - without moving the straightedge - scribe the line. Use scribes, rather than pencils or pens, because they make more precise marks.
The tutorial that I am sharing here was written by someone who built this pallet art just to improve the value of a property they wanted to sell fast and they succeed in it. So you can imagine how wonderful this item must look like. I am assuming you do not just want to make this beautiful pallet art so that you can also sell your property easily. Well, whatever your reasons are, this beauty is able to attract anyone who visits your house.
The decision to be made with respect to the end vise is whether the support plate should be mounted to on the inside or on the outside of the stretcher. Mounting the plate on the inside of the stretcher reduces the reach of the vise - it can't open as far, because the support plate is back from the edge by a couple of inches. But mounting the plate on the outside of the stretcher means that we need to add some support structure for the inner jaw of the vise, which the legs would have provided if we'd mounted the plate on the inside.

To mark the centerline, set a compass to span something more than half the width of the leg. Draw an arc from corner of the leg. The point where the arcs intersect will be on the centerline. With a centerline point on each end of the leg, place a scribe on the point, slide a straightedge up to touch the scribe. Do the same on the other end. When you have the straightedge positioned so that you can touch both points with the scribe, and in each case it is touching the straightedge - without moving the straightedge - scribe the line. Use scribes, rather than pencils or pens, because they make more precise marks.
In terms of size, this bench is another Sjobergs that is a bit on the small side, though it is actually far more squared than some others. While its length is a bit disappointing at 54″, the width is over 24″ wide which does provide for more diverse projects. Even better, this product still features the incredibly 500-pound weight capacity and continues the Sjobergs trend of avoiding joints that are not as durable as they otherwise could be.
Foundations of Woodworking runs every fall (September - December) and winter (January-March). The application process for each session opens 9 months in advance of the course start date. Applications will be considered for registration in the order in which they are received. There is no fee for applying. Accepted applicants will be invited to register. We ask for a deposit of $200 at the time of registration to ensure your place in the class. 
Sjobergs’ woodworking benches are recognized all over the world for their durability, handy design and extra features that make these benches well worth the money. This Hobby Plus bench is the perfect fit for a woodworking enthusiast, especially since it is equipped with two vices and bench dogs. This could become your one and only woodworking station!
I was using 2-1/2" coarse Kreg pocket hole screws. Kreg screws are supposed to be self-tapping, but the coarse-thread screws are intended to be self-tapping in softwood, and the fine-thread screws they intend for use in hardwoods aren't available in 2-1/2" lengths. I decided to drill pilot holes in the oak. Just to make sure, I did a test hole in the scrap piece I'd cut off.
While $115 may seem expensive, try accurately boring a grid of 20mm holes on 96mm centers in 3/4 MDF. I have for a table for our retirement community shop - - its a pita. Plus the MFT material seems denser and more water resistant than garden-variety MDF. And the single-thickness has proven sufficient the last several years on my original 1080s. Still dead flat.
I decided to finish the top with a number of coats of Danish oil, followed by a coat of wax. I applied the first coat of oil in the usual manner, making sure to cover the edges, and down the holes. I applied a coat oil to the top side of the shelf, as well. Wipe it on, let it sit wet for half-an-hour, then rub it off. Wait a day or two, add a second coat, and then again for a third.
In general, students in the certificate and degree programs learn how to understand and create their own shop drawings and design custom cabinetry. In the process, they also find out how to use the same tools and machines employed in the woodworking business and assemble cabinets according to industry standards. Additional program topics include the use of contemporary hardware in design.
My first shop was a 8 x 10 ft room, actually a bedroom, with 10 ft high ceilings in a older home in Chicago. I had a 10" Craftsman TS, drill press, 8 1/4" Skil saw which still works, some welding tanks, hand tools and... my bed was a loft across the 10 ft length 4 ft down from the ceiling with a ladder against the wall to get up. I was 16 yrs old then, now I am 66 yrs, have 2 shops with Craftsman power tools up stairs, and Grizzly tools ,a Powermatic 68, a MIG welder, and other tools on the ground floor. I've come a long way, You think? I remember making bases for sculptures called "plinths", my first commission, in the living room, 5 pieces rather large, several ft long and wide. The house was haunted, and my mom told the "spirit" to leave and go back downstairs. There was a cold draft and the straw chair would rustle with no one sitting in it. Wow, does that bring back memories from the '60's.
We are especially proud of Post Woodworking’s Brunswick style shed. It has all the rugged features and simple, beautiful mystique of a Maine coastline. Natural-wood siding options, in pine or cedar, offer a rustic aesthetic. Or, choose a vinyl color that complements our home. Once inside the Brunswick, its unique, two-sided sloped roof maximizes headroom, making space for you to better maneuver a rake. Black architectural hinges and hardware lend distinguished contrast and quality to this basic but appealing storage solution.
×