Let me see if I can come up with a couple details. The table saw is a TS3660. So I have heard, this should be the center of your shop. My jointer is a 6 1/8" Jointer / Planer JP0610 which is 45 inches in length. My router table is the kreg router table that takes up a 24 x 32 inch footprint. My bench is roughly 30 x 70 inches and my bandsaw is 3' x3'. I have other tools as well such as a portable 12.5 Delta thickness planer in addition to a wall mounted dust collector. To add to the list, I am just about to get a 10 inch makita sliding compound miter saw. I can see how space will be eaten up quickly. Any ideas as to how arrange these tools in such a small shop? I will get pics a soon a I


I mocked up the two scenarios, and determined that with the plate inside the stretcher the vise would have a reach of 8 inches, and with it outside the stretcher it would have a reach of 9 inches. I decided that 8 inches was enough, and that the extra inch wasn't worth the extra effort. With the end vise mounted like this, the right edge of the top would have no overhang.
One quality about this bench that is definitely lacking is space – both tabletop and storage. The Olympia Tools does provide an adequate shelf, but it does not come with any drawers, nor does it offer the option of adding them later. The table top is the smallest we saw at 50” long and 2’ wide, though the width is actually better than most of the other table we reviewed. Still, a significant chunk of that width is occupied by a trough. This trough is designed to hold smaller workpieces to keep them from falling or getting knocked over, but it removes about 6” of width from the tabletop.
Working with wood fresh from the log, this green woodworking project is the perfect introduction to edge tools and wood grain.  In the first week you will produce a three-legged stool using buck and “whip”saws for crosscutting the log to length; wedges and froes for splitting out leg stock; drawknife and spokeshaves at a shaving horse for shaping the legs; and using travishers, rounding planes and specialized rasps for shaping the seat.
You can buy sandpaper, glue, and other consumables from them for a nominal price. Their hand tools are propitiatory though so you would have to buy a specific kind of orbital sandpaper, for example. You couldn't just get generic. They are reasonably priced though. There is literally a coffee can with money in it and prices written on the boxes with these consumables. If you think you might burn through enough sand paper on something, check the brand and price shop.

Fundamentals Of Fine Woodworking With Taeho Kwon (Evening Class) The secret to fine woodworking can be found in the pursuit of the fundamentals. With high-tech machines and power tools, these fundamentals can be overshadowed. In this class we will learn the values of design, drawings, mock-ups, sharpening, care and use of hand tools, tuning up a bench...
What I did, when I came back, was to clamp down the strip where it had torn away, and then to start routing from the other end. I still moved the router from right to left, but I did it in six-inch sections, taking light passes, and sort of whittled the strip flush. As the sections I was working were farther to the right, the strip was thinner. Eventually I came to where I was trimming the strip away entirely, at which point I took off the clamps and the remainder fell away.
I used the factory edge of the half-panel of hardboard as a guide for cutting the ply. I wanted to cut a 5-1/2" strip, and my saw cuts 4-1/2" from the edge of the shoe, so I wanted the edge of the hardboard 10" from the edge of the ply. So I set my combination square to 10", and used it to mechanically set the distance. Hint - if you need two things to be precisely the same length, try to avoid measuring them separately. Use some mechanical mechanism for setting the distance.
Thread the rods through one of the legs, then set the leg flat on the table. Insert dowels into the dowel holes. Place the matching stretchers into place. Put dowels into the dowel holes at the top end of the stretchers. Place the other leg onto the threaded rod and settle it down onto the dowels. You'll probably have another opportunity to whack away with your rubber mallet.
First, we need to drill out the holes for the screws that will hold them together. While the two layers of MDF are glued, the countertop and the MDF will only be screwed. The oak countertop, like any natural wood product, will expand and contract with humidity changes. If it were glued to the MDF, the difference in expansion of the two layers would cause the countertop to buckle and curl.

Thanks Chris! I found this page while looking for a link to your e-mail address. I recently finished your erudite volumes on workbench design, and am about to embark on my own bench inspired by your take on the Holtzapffel design. As my vices and planer arrive, I’ve been agonizing over whether to use SYP or rough maple for the top. I don’t have a big budget, so all-maple is not an option. But after reading your ten tips here, I’ll stop agonizing — all SYP it is! This is, after all, my first of what I hope are at least several handmade benches. Your scholarship and craftsmanship are truly inspiring.


Cerritos College in Norwalk serves over 21,000 credit students each year with certificate and degree programs for recent high school graduates and adult learners. The Cerritos College Woodworking school is housed in 27,000 square-feet of space and is equipped with over 100 woodworking machines. Under the direction of 20 instructors, the school offers more than 50 classes in woodworking, including those in architectural millwork, cabinet and furniture making, routing and veneering.
Why would you buy a costly platform bed from Ikea or somewhere else when you can make one yourself at home? Oh yes, you can. A bed is the most common furniture piece used in the house and probably the costliest one. Wouldn’t it be great if you could just make a bed of your own, without having to spend many bucks for buying one? So I am here sharing a great tutorial to help you to build a nice comfy platform bed that you can use anywhere in the house.
If you're using drywall screws, you'll want to countersink the holes. Drywall screws are flat-head, and need a countersink to seat solidly. If you're using Kreg pocket screws, the way I did, you won't want to counter-sink the holes. Kreg screws are pan-head, and seat just fine against a flat surface. Both drywall screws and Kreg pocket screws are self-threading, so you don't need pilot holes in the second sheet of MDF.
1. You mention doing other hobbies which I assume means stuff scattered around for various projects. (Don't tell me you do one at a time or are a neat freak!!!) How tall are the side walls to the shed? How high do you shuffle stuff around, i.e. flipping things over, moving wood around, etc? I can't imagine trying to do that in my shed, even if it were 2 ft higher than it's 7 ft center height. If you could build a platform in front it may help, especially if you can put removable cover over it (to please HOA).
×