I really like this. I've been busy designing my own workbench to replace the ropey old thing I currently use. You've made me reconsider exactly what I need a bench for - I think I've been more than a little seduced by the idea of a beautiful hardwood bench when, if I'm honest, I don't need one. My cash would be better spend on timber for furniture projects that my family can enjoy rather than a wonderful workbench that I can only use on the weekends.
Palomar Community College in San Marcos, located about 35 miles north of San Diego, offers certificate, degree and life-long learning programs to more than 20,000 students a year. In particular, the Cabinetmaking and Furniture Technology Department offers in excess of 50 classes annually, and the present faculty is composed of four full-time teachers, 21 part-time instructors and 11 teaching assistants. As of Fall 2013, woodworking students will have access to a newly remodeled woodworking facility equipped with three machine rooms, three bench rooms, a saw mill and a finish room.
Students who are interested in woodworking, either as a career or a hobby, can find classes through certificate and vocational degree programs. Furniture making and opportunities for wood sculpture can also be found at schools that offer studio art programs. In California, a wide range of programs in the field are available, including individuals classes as well as formal educational programs. While degree programs include general education programs, all woodworking programs focus primarily on the development of hands-on skills with respect to safety measures.
Great advice. May I add #11?…if you’re left handed (like me), build a left handed bench. It sounds obvious, but when I made my bench, I had looked at all the pictures in my books, laid out plans for a nice, traditional bench, built it, then realized my front vise should have been on the other end (I have no tail vise). I plane from left to right, and the front vise is always in the way.
Whether you want to build your own kitchen cabinets, a credenza for your dining room, or built in shelves for your bedroom you should have some basic cabinetry skills before getting started. There are so many options when designing and building cabinets: face frame vs. frameless; sliding vs. hinged doors; dovetails vs. rabbets; plywood vs. MDF; wood...
The holes we want to mark are the holes through which the threaded rod connecting the two legs will run. This threaded rod will run through the 3/8" groove along the bottom of the short stretchers,. The hole for the upper stretcher has to be positioned so that when the rod is running through this groove, the top of the short stretcher is even with the top of the legs. The most precise way I've found for marking the position of this hole is to use a dowel center. Fit the dowel center into the bottom groove, line up the stretcher, and bang on the end with a rubber mallet. The dowel center will leave a mark indicating the center of the hole.
When the top is done, we want the edged MDF and the oak countertop to have exactly the same dimensions, and for their width to exactly match the width of the base.I could see three ways of doing this: 1, join the MDF to the countertop and use my belt sander to sand down their joined edges to match the base; 2, join the MDF to the countertop and use a hand plane to plane down their joined edges to match the base; or 3, use a flush-trim bit against a straight edge to route the MDF to the width of the base, then join the MDF to the countertop and use the flush-trim bit to route the countertop to match the MDF.
Fundamentals Of Fine Woodworking With Taeho Kwon (Evening Class) The secret to fine woodworking can be found in the pursuit of the fundamentals. With high-tech machines and power tools, these fundamentals can be overshadowed. In this class we will learn the values of design, drawings, mock-ups, sharpening, care and use of hand tools, tuning up a bench...
@cahudson42 I bored the holes in my sandwich top with a 3/4" power auger bit with the drill in a portable drill guide that kept it vertical and in a way a bit like a plunge router. The guide screw of the auger was dead easy to centre over the laid out grid points. The holes are dead straight and clean sided. The auger bit was new which probably helped. As stated I have three rows from an end vise running the length of the front as well as from the front vise and holes in the front apron to support long pieces as well.
Working with reclaimed wood is a savvy use of resources, and the material's country appeal is undeniable. With just a saw and a small drill, you can reuse old fencing to make these simple woodworking projects: picket-inspired picture frames. Finish them off by hot-gluing clothespins or bulldog clips to hang your prints. Here’s a step-by-step guide.
This trade and technical college currently serves over 15,500 credit students from its campus in downtown Los Angeles. Through the Construction, Design and Manufacturing Department, full-time students can enroll in a daytime certificate or an Associate of Science program in cabinet and millwork. Evening programs for current craftspeople include a certificate program in construction technologies and an Associate of Arts in cabinetmaking and millwork that provide students with the skills they need to work in construction or manufacturing.
I had a similar experience with running electrical power to a shed. It turned out that I could build a 12x12 shed without a building permit as long as I did not run utilities, but getting a permit opened a whole new set of requirements that forbid me from having a shed at all. And when the nosey old woman next to me kept calling the building inspector on me, it was suggested that I could run an extension cord out to the shed anytime I wanted as long as it wasn’t fastened in a permanent manner.