I made my version of a Roubo bench over 20 years ago. According to the latest bench rules it is too tall, too wide, has too many vises (I use both sides of my bench and that might be a no no, not sure ), and has far too many holes. Did I mention that I have a double row of dog holes with a user made dual row wagon vise? I had no idea they were called a wagon vise back then. Being a tool maker and tinkerer at heart I just made a vise that I thought at the time was an original idea for the main side. Couple of dowels in a piece of wood straddling the two rows and I have a bench stop, or a different variation gives me a 3 point clamping system. If that isn’t bad enough it also has drawers on the bottom to store seldom used tools and supplies. Maybe if it had taken me a few weeks to drill all those holes and mount a few vises I would only have one vise and 8 holes too. I dunno
Isn’t this amazing that instead of having to throw that old furniture piece away, you can now reuse it to build something even more beautiful? If you do not like this particular idea, there are many other re-purposeful furniture items you can build from an old dresser. Just search the internet for other DIY project ideas. Here is a link to the video tutorial that explains the same procedure in a more practical manner that you can easily follow through.
The reason I'd cut out the rectangles in the vise support was that I'd intended to put a benchdog hole through each, and I wanted the thickness of the top to be the same for all of the benchdog holes. Where I messed up was in not cutting out the ends, between the bolt tabs. I'd intended to put a benchdog hole through there, as well, but I'd forgotten to cut out the segments prior to glue0up.
Those bums even have a stipulation that you can't connect any utilities to a shed. My plan is to adhere to the letter of the law if not the spirit. I plan to run a buried 20 amp power line out to the shed (this will be done professionally and properly according to whatever is required by the law), but it will require a manual connection to a junction box on the outside of my house to complete the circuit. That way, I can argue that the electrical connection is only temporary and is little more than a safe and buried version of an extension cord.
In class, each student will build a detailed hall table that is complete with mortise and tenon joinery, biscuit, dowel, and floating joint construction. The student project is presented with a variety of design options and formats as to meet the experience and comfort level of each student. Depending on their experience and comfort level, students are encouraged to make a simplified version of the hall table or tackle a more sophisticated and complicated version of the same project. Your only limitation is the amount of material you receive in your lumber pack (~24 board feet).
The edges of MDF are fragile, easily crushed or torn. MDF is also notorious for absorbing water through these edges, causing the panels to swell. In Sam Allen's original design, he edged the MDF with 1/4" hardboard. This edging is one of the complexities that Asa Christiana left out in his simplified design. I think this was a mistake. MDF really needs some sort of protection, especially on the edges.
For most of the course, we'll be heavily focused on developing your skills using hand tools. As a developing woodworker, there is no substitute for putting in the hours of direct hands on practice it takes to gain an intuitive understanding of wood. The early part of this course focuses on working with hand tools as we believe they bring you closer to wood as a material. You can rip a board on a table saw with out much thought to the wood itself, but you will understand much more about grain if you rip a board with a hand saw. As the course progresses, machine processes are introduced as a pragmatic aid in expediting projects.
Remove the jaws and route the edges that you could not route while they were still attached. Then use a roundover bit on all of the corners except the inner edge of the inner jaw of the end vise. Give everything a lite sanding, and apply Danish oil to the inner surfaces of the jaws. (By "inner surfaces", I mean those surfaces that will not be accessible when the vises are assembled - the inner surface of the inner jaw, that bolts to the bench, and the outer surfaces of the outer jaws, that bolt to the vise plates.)
Having done all this, I'm not sure I'd do it this way again. It might well be faster to layout the positions with compass and straightedge directly onto the top. Either way, you'll want to use a scribe rather than a pencil. Scribe lines are hard to see, and impossible to photograph, but the scribe and compass points click into them, allowing a precision that pencils simply cannot match.
Not sure about Midwest but I have a 24 x 14 Game rm attached to my shop and I put a small window unit/heat pump in the wall. It stays comfortable all year round. It get really hot here and we had a several day in the 20's this winter but it's insulated well. That might not be as cold or as hot as in some places but the unit I haze does not run that often and has a low cost rating. I'm planning on putting a larger unit in the shop area even though I do like to work with the garage door open. The door is insulated so I can run A/c in there. Just my .02.
As simple as its elements are, the workbench is more than a tabletop with legs, a well, and a few holes. Virtually everything in the workshop comes to rest on the bench at some point, even if only between operations at other stations. Planning and layout, cutting and shaping, assembling and finishing–all can be, and often are, performed on the benchtop. The better the design, and the better suited its size and configuration to your labors, the more efficient a tool it will be.
I had a similar experience with running electrical power to a shed. It turned out that I could build a 12x12 shed without a building permit as long as I did not run utilities, but getting a permit opened a whole new set of requirements that forbid me from having a shed at all. And when the nosey old woman next to me kept calling the building inspector on me, it was suggested that I could run an extension cord out to the shed anytime I wanted as long as it wasn’t fastened in a permanent manner.