Learn to use hand and power tools to shape wood into objects that will last for decades. You’ll learn about the properties of lumber, safe tool use, measurement and layout, and fundamental woodworking joints. At the end of this week-long course, you’ll leave with an end-grain cutting board, a mitered corner box, and the skills to build an unlimited range of wooden objects.
I made a low table out of a couple of step-stools, my hollow-core door, and one of the MDF panels that would eventually form part of my top. I was concerned that any oil that dripped on the door might interfere with its glue adhesion, when I finally get around to the project for which I'd purchased it. The top side of the top sheet of MDF, though, I planned to oil, anyway. (Ditto for the bottom side of the bottom sheet.
Assemble the vises, for the final time. You'll not be taking them off again, so tighten everything down, and attach the endplate to the ends of the screw and guide rods. Then mark and drill benchdog holes in the outer jaws inline with the benchdog holes in the top. Generally, through-holes are preferred for benchdogs, so that they don't collect sawdust and gunk. With these vises, that isn't possible, there are screws and guide rods in the way. I drilled them just deep enough to hold a Veritas Bench Pony (their reduced-height benchdog), without it sinking to where I can't get a grip to remove it. Rockler sells some very inexpensive plastic benchdogs that can't be adjusted for height, and aren't as strong as metal or wooden dogs, that I intend to keep in the holes full-time, to keep sawdust from collecting in them.
I ended up making a number of practice cuts. The first revealed that I hadn't tightened the screws on the edge guide enough. The second revealed that the design of the edge guide provided very little support at the end of a board, because of the cut-out for the router bit. In the "Getting Started in Woodworking" video, they had screwed a piece of hardwood to the edge-guide, to provide a continuous -- and longer -- bearing surface. I may do that myself, some day, but I didn't have the materials at hand, so I clamped some 2x4 scrap to the end of each board, to provide a continuous bearing surface past the ends. The two grooves in the long stretchers and the side groove in the short stretchers have identical layout. I made practice cuts in scrap until I had the edge guide set correctly, then I cut them all with that one setting. The bottom groove of the short stretchers uses a different setup, so it was back to the scrap, before cutting them.

For a fun and comprehensive learning experience, take an online woodworking class in the WWGOA Academy. You’ll learn in-depth woodworking how-to, get bonus material, and enjoy custom benefits for class participants. You’ll never lose access to your Class; no strings attached! Check back often – as we’re adding new online woodworking classes regularly.


These things may be tiny in size, but building one is not that easy. It takes some serious woodworking knowledge and skill to build a nice wooden mobile stand. When I first saw one online, I just couldn’t resist thinking of buying one. But when I saw the price, I was forced to rethink. Also, a woodwork lover like me cannot be contained with just one piece and I was not willing to spend on more than one. So instead I decided to build myself one. Yes, it took some doing but the final result was satisfying. Luckily, I found this awesome tutorial online that helped me build my first ever wooden phone holder.
I am sharing here a link to the detailed tutorial written by Pete at diypete.com, who shares the step by step process for making a wonderful barrel coffee table from scratch. He also tells you what items you’ll need for this project and where to find them. For example, you can buy an old whiskey barrel online or from a local whiskey store for a few bucks, if you haven’t already got one.
Students who are interested in woodworking, either as a career or a hobby, can find classes through certificate and vocational degree programs. Furniture making and opportunities for wood sculpture can also be found at schools that offer studio art programs. In California, a wide range of programs in the field are available, including individuals classes as well as formal educational programs. While degree programs include general education programs, all woodworking programs focus primarily on the development of hands-on skills with respect to safety measures.
Cerritos College in Norwalk serves over 21,000 credit students each year with certificate and degree programs for recent high school graduates and adult learners. The Cerritos College Woodworking school is housed in 27,000 square-feet of space and is equipped with over 100 woodworking machines. Under the direction of 20 instructors, the school offers more than 50 classes in woodworking, including those in architectural millwork, cabinet and furniture making, routing and veneering.

Thanks Chris! I found this page while looking for a link to your e-mail address. I recently finished your erudite volumes on workbench design, and am about to embark on my own bench inspired by your take on the Holtzapffel design. As my vices and planer arrive, I’ve been agonizing over whether to use SYP or rough maple for the top. I don’t have a big budget, so all-maple is not an option. But after reading your ten tips here, I’ll stop agonizing — all SYP it is! This is, after all, my first of what I hope are at least several handmade benches. Your scholarship and craftsmanship are truly inspiring.
Getting a smooth, blemish-free finish with oil-based polyurethane is within your grasp if you follow the steps in this article. Oil-based polyurethane varnish brings out the wood’s natural beauty or wood grain. Our 4-step approach shows you how to apply the varnish successfully. A good-quality natural-bristle brush, a reasonably dust-free, well ventilated space and some patience are all you need. Learn how to apply polyurethane.

I used the factory edge of the half-panel of hardboard as a guide for cutting the ply. I wanted to cut a 5-1/2" strip, and my saw cuts 4-1/2" from the edge of the shoe, so I wanted the edge of the hardboard 10" from the edge of the ply. So I set my combination square to 10", and used it to mechanically set the distance. Hint - if you need two things to be precisely the same length, try to avoid measuring them separately. Use some mechanical mechanism for setting the distance.
My bench is MY BENCH. In other words, it’s a thing of evolutionary beauty. I built the top 10 years before deciding on and designing the base. I spared no absurdity. It is supremely stout and the much maligned drawers are accessible from either side. The larger drawers have dust lids and can be extended to provide support for large workpieces or as a step for climbing on top of the bench. The top alone weighs more than most Roubos. So NYAH! Did I mention that I designed it to fit in with the Arts & Crafts vernacular? Who said you can’t build your bench to be furniture? Beautiful as well as useful shop furniture? Just sayin…
Flip the base upright, put the MDF on top of it, then use a straightedge to draw two straight lines joining the outside edges of the legs and extending the width of the MDF. I used the countertop as the straightedge. We cut it with our cutting guide, which is based on the factory edge of a sheet of 1/4" plywood, so it should be straight enough. Use a carpenter's square to transfer these lines onto the ends of the MDF.

Thinking about transitioning into serious woodworking, but don't have half a year or more to spare? Our one-month fine woodworking courses are perfect for those who are looking to move towards professional woodwork, but can’t find the time to commit to a longer course. Here, our woodworking classes will intricately teach you all of the basics, the same as you would for our three, six and twelve-month courses, with projects specially-created for both beginners and the more experienced. This will truly bring your woodworking skills up to the high level of craftsmanship needed within the industry.
The edges of MDF are fragile, easily crushed or torn. MDF is also notorious for absorbing water through these edges, causing the panels to swell. In Sam Allen's original design, he edged the MDF with 1/4" hardboard. This edging is one of the complexities that Asa Christiana left out in his simplified design. I think this was a mistake. MDF really needs some sort of protection, especially on the edges.
The projects in this course follow a natural progression of skills, techniques and tools. Some of the early student-made tools are, in fact, used to help make the next tool or bench fixture in the series. You are supported in the building of these projects with step-by-step outlines, knock-down examples and continuing, one-on-one consultations with the faculty. Periodic evaluations of your progress with a specific faculty-mentor help keep you on track.
Cerritos College in Norwalk serves over 21,000 credit students each year with certificate and degree programs for recent high school graduates and adult learners. The Cerritos College Woodworking school is housed in 27,000 square-feet of space and is equipped with over 100 woodworking machines. Under the direction of 20 instructors, the school offers more than 50 classes in woodworking, including those in architectural millwork, cabinet and furniture making, routing and veneering.
Drill a pair of 3/8" holes in each end of the short stretchers, just over half of the depth of the dowels, using a brad-pointed bit. These stretchers already have a groove running their length, centered on the bottom edge. Precise placement isn't necessary, but keeping track of which part is which is. We need a hole in each end of each stretcher. Take care to keep these holes square, you don't want them running at angles.
My advice? Don't do this. If you have jointer and a planer, use them. If you don't, seriously consider using dimensional lumber that has already been planed and sanded. If you are going to try to clean up construction lumber by hand, using a hand plane is a lot faster and more pleasant than using a belt sander. Except, of course, that to do a good job of planing a board you need a solid bench to hold the board, and you don't have a bench, yet.
Chris I blame you for all these altars that are being built today and now you thinks we over thinks ’em–huh. You whipped the masses into a frenzy— now Woodworkers are trying to out pretty each other–out wood species each other –out Rube Goldberg each other. I made 2 benches in 30 years neither had a through dovetail but many were made on them and I have no idea but I would bet a dollar that neither weighed 280 pounds but they both had tons of wood on them. If you want the bench as a destination god bless but it was intended as a mean. Thats my rant I could be wrong
If you remember, when drilling the MDF I finished the holes from the other side using a Forstner bit. It made for a clean hole, but the positioning wasn't as precise as I really wanted. So for this, I decided to clamp a length of scrap MDF to the back side, and to drill straight through. My Forstner bits were too short, so I bought an extender. And then I found that the spade bits I was using gave a cleaner exit hole. Whooda thunk?
The Community Woodshop allows me to have access to a countless number of the best quality tools in the industry. They are always on top of keeping everything working and running.  If anything breaks they are always very proactive in fixing things ASAP.  They also have more than enough tools so I never have to wait to use a sander or any of the smaller tools, and I have never had to wait more than a few minutes to get on the table saw (and even that is rare).

This course will drill deep into the basics, beginning with a firm foundation in understanding wood as a material and incorporates introductory training in a wide range of techniques. You'll leave with a in depth experience of hand tools, practice applications of joinery methods, consider choices for wood selection and working with non-toxic materials, and understand practical planning for designing and executing woodworking projects.  The curriculum focuses on imparting skills through a series of projects designed to build on one another in techniques and complexity. 
Learn basic principles of working with wood while making your own carved wooden spoon. Topics covered include different types of wood, grain direction, carving, shaping, and food safe finishes. Through short demonstrations and lectures, we will use a combination of power and hand tools, exploring the material for its functionality as a creative medium. At the end of the workshop, students leave with a unique spoon, ready to use! All materials included.

The first time you try your hand at the ancient craft of woodworking, you want to do it right. Learn woodworking basics with hand tools to a professional standard on a weekend woodworking course at Rowden Atelier. Ed Wild runs weekend furniture building courses for everyone from beginners who want to have some fun experimenting behind the bench, to those who are looking to develop specific skills as a furniture maker. Classes include tool handling, box making, and basic veneering, but to a certain degree, you can tell us what you want to learn - these short woodworking courses are partly bespoke.
The edges of MDF are fragile, easily crushed or torn. MDF is also notorious for absorbing water through these edges, causing the panels to swell. In Sam Allen's original design, he edged the MDF with 1/4" hardboard. This edging is one of the complexities that Asa Christiana left out in his simplified design. I think this was a mistake. MDF really needs some sort of protection, especially on the edges.
I live in VA and my workshop is an unheated, uninsulated garage. I work out there year round, even when temps are below freezing. I can't say it's comfortable in the winter (or when it's 100 degrees with 95% humidity) but I haven't had any major issues. I have had some big box green wood warp on me after I built a couple bookshelves and brought them into the house, but that was more a factor of the green wood than my "shop".
×