It doesn't get much better than a day at the woodshop! I've taken several classes from cutting boards to turning vases. It is always fun and informative! All of the machines are top notch and the instructors are great! I've toyed with the idea of a membership but I think I'll take a couple more classes before doing so! I can't wait to see the new location! :)

Woodworking has a rich place in the history of human civilization. Used for thousands of centuries, it provided early cultures a way to construct shelters, furniture, boats, and more; in doing so, it made life easier and ultimately allowed a society to advance. The art of woodworking continues today, having survived a myriad of design aesthetics (including the not-so-wood-friendly Memphis Design). To pay homage to this ancient craft, one Instagram account called @wooodworking features pieces from different artists and artisans around the world.
Having done all this, I'm not sure I'd do it this way again. It might well be faster to layout the positions with compass and straightedge directly onto the top. Either way, you'll want to use a scribe rather than a pencil. Scribe lines are hard to see, and impossible to photograph, but the scribe and compass points click into them, allowing a precision that pencils simply cannot match.

Do you want to use an oil stain, a gel stain, a water-based stain or a lacquer stain? What about color? Our ebook tells you what you really need to know about the chemistry behind each wood stain, and what to expect when you brush, wipe or spray it on. It’s a lot simpler than you think! This is the comprehensive guide to all the varieties of stain you will find at the store and how to use them.
Chris I blame you for all these altars that are being built today and now you thinks we over thinks ’em–huh. You whipped the masses into a frenzy— now Woodworkers are trying to out pretty each other–out wood species each other –out Rube Goldberg each other. I made 2 benches in 30 years neither had a through dovetail but many were made on them and I have no idea but I would bet a dollar that neither weighed 280 pounds but they both had tons of wood on them. If you want the bench as a destination god bless but it was intended as a mean. Thats my rant I could be wrong
This is not exactly a tutorial, but a guide to some really cool woodworking projects. Although we are not teaching you to make anything, we are always here to help. Feel free to ask your queries in the comments in case if you face any issue while working on any of these projects. Also, tell us how much you liked this article. Did you enjoy reading it? Did you work on any of these projects, and if yes, how was your experience? You are also welcome to share any images of your completed woodwork projects.
Relax and enjoy your outdoor space with this smart patio combo consisting of a sofa and chair. You can adjust the size completely to make it fit perfectly onto your patio or deck, and both the sofa and chair have arms that double as trays for al fresco dining. And you can make your own cushions to fit, or use shop-bought ones and add your own ties, if necessary.

This particular tray is made using reclaimed barn wood but the author of the project Beyond The Picket Fence surprised everyone with one fact: reclaimed barn wood has often some areas turned pink due to cow urine. If you check the project more closely, you’ll also notice some areas of the tray being almost bright pink. That’s something you don’t see every day!
A better solution would have been to route a rabbet into the side, so that the added strip always had thickness. The way I did it means that the strip I glued in is very narrow, and hence very weak, at a certain point. In this case, that's not a problem, because it's going to be sitting under the countertop layer. I also noticed that because I had only clamped the strip down, and not into the edge, there was a noticeable glue gap where the strip butted up against the MDF. Again, in this application it isn't visible. But if I was doing something like this on the top of a table, I'd make sure to cut a clean rabbet, and to clamp both down and in.
AJ and Scott have been very helpful showing me where tools are my first few days there. This is a workshop where you will have to work independently. They will show you how to use certain machines for the first time and orient you to the shop itself but they will not help you with your project.  They can, however, be hired to help you with projects if that's what you need. I believe it's $75 an hour and limited to their availability. There is also a host of classes you can take if you want an intro into cabinet making, wood joining, turning etc. There are a lot of different classes that may pique your interests.
Clamp the inner jaw of the end vise in position, leaving a little bit to trim off later, and then use the dowel and dowel center trick through the screw and guiide rod holes of the vise base plate to mark the position of the screw and guide rod holes in the jaw. Remove the jaw and drill 1-1/8" holes in the marked positions. I used the drill guide for most of the holes, and drilled freehand for the last bit. When you're starting a spade bit in a deep hole like this, start the drill very slowly, and the bit will move the drill into a perpendicular position. Start it too fast and the bit will bind and you'll damage the sides of the hole.
AJ and Scott have been very helpful showing me where tools are my first few days there. This is a workshop where you will have to work independently. They will show you how to use certain machines for the first time and orient you to the shop itself but they will not help you with your project.  They can, however, be hired to help you with projects if that's what you need. I believe it's $75 an hour and limited to their availability. There is also a host of classes you can take if you want an intro into cabinet making, wood joining, turning etc. There are a lot of different classes that may pique your interests.
In this two day class we will reveal some of the secrets to tuning up a Japanese Hand Plane (Kanna) We will start with conditioning the Body of the Plane (DAI) to stabilize movement. Proper sharpening and grinding of the blade and chip breaker will be discussed and demonstrated. Custom fitting the blade to the Dai and conditioning the sole. We will...

I agree that even at 12x12, things'll be "cozy" inside. That's OK. Keep in mind that this will be a general purpose hobby shed, not just a wood working shed. Even 12x8 would be plenty big enough for building 1 meter wingspan bungee launched RC gliders. And for the electronics projects I do, I only need enough workbench space to do some soldering with a 3rd hand (for electric guitar pedals). If I need more room than the shed offers for wood working projects, I'll just roll the table saw down a ramp and do my cutting outside in the sun.
I live in the second rainiest city in the country, Pensacola, so I am used to dealing with wet. I literally work out of my garage (read storage area, small woodwork area, washer/dryer...car? ). I wheel bigger tools and table out to the little covered area in front of the garage. I have an 8 x 10 aluminum shed that is strictly garden stuff storage. I mention this for two reasons.
×