My name is Takami Kawai and I'm a traditional Japanese carpenter and architect with over 16 years of experience in sustainable design and construction. As much as conditions allow, I enjoy using traditional Japanese techniques. My experience includes working for the world renown, Ise Jingu Grand Shrine. I have also hosted numerous presentations on traditional Japanese woodworking. Now, I run a small construction firm, Suikoushya, which specializes in the restoration of traditional Japanese houses.

In the Port Townsend School of Woodworking’s twelve-week Woodworking Foundation course, you will learn the essential skills, tools and mindsets of the traditional joiner. This is NOT an industrial arts course with a focus on machinery and production processes. Rather, it is a course in PRE-industrial artisanship--the creation of individual works through mostly hand tools and skills.. 

Great advice. May I add #11?…if you’re left handed (like me), build a left handed bench. It sounds obvious, but when I made my bench, I had looked at all the pictures in my books, laid out plans for a nice, traditional bench, built it, then realized my front vise should have been on the other end (I have no tail vise). I plane from left to right, and the front vise is always in the way.
The video explains the step by step process of making a nice wooden phone stand from scratch. My first wooden holder was not the best one, but it was good enough to motivate me to make more. I now possess 10 mobile wooden stands in different shapes and styles. And if I can make this, you too can make one yourself. Search the internet for more mobile holder ideas and start making one now.
Laney College is located in Oakland near the San Francisco Bay and currently enrolls around 12,000 students. The Wood Technology Department offers 1- and 2-year certificate programs in wood technology, computer-aided drafting and design, as well as an apprenticeship program and carpentry courses. Students have access to eight faculty members and a variety of woodworking machinery and equipment, including a lathe.
With the top laying on the floor, bottom side up, the next step is to flip the base upside down, and attach it to the top. I followed Asa Christiana's design, in using s-clips. When I stopped by my local Woodcraft, though, they only had two packages of ten, so I didn't use as many as I would have, otherwise. For the top I put four on each side and two on each end. For the shelf I put three on each side and two on each end. If it turns out that I need more, I can always add more.
Clamp the inner jaw of the end vise in position, leaving a little bit to trim off later, and then use the dowel and dowel center trick through the screw and guiide rod holes of the vise base plate to mark the position of the screw and guide rod holes in the jaw. Remove the jaw and drill 1-1/8" holes in the marked positions. I used the drill guide for most of the holes, and drilled freehand for the last bit. When you're starting a spade bit in a deep hole like this, start the drill very slowly, and the bit will move the drill into a perpendicular position. Start it too fast and the bit will bind and you'll damage the sides of the hole.

Evidence of a removed fireplace makes it clear that the woodworkers were doing tasks that required warmth, like using glue. The type of glue used during that time had to be heated to a certain temperature. Bill Flynt, a former colleague of Garrison, tested the wood of the shop and found that it is second- or third-generation wood, meaning that New Englanders had already cut down and replanted lots of trees by that time.


I made a low table out of a couple of step-stools, my hollow-core door, and one of the MDF panels that would eventually form part of my top. I was concerned that any oil that dripped on the door might interfere with its glue adhesion, when I finally get around to the project for which I'd purchased it. The top side of the top sheet of MDF, though, I planned to oil, anyway. (Ditto for the bottom side of the bottom sheet.
A woodworker's Workbench is a special type of bench designed to hold your work when you are working on a wood project. The main purpose of this table is to keep the woodwork steady and to prevent it from moving. Follow the tutorial below to build yourself a nice workbench suitable for your specific woodworking projects. Make sure to modify the table to fit your specific requirements.
@cahudson42 I bored the holes in my sandwich top with a 3/4" power auger bit with the drill in a portable drill guide that kept it vertical and in a way a bit like a plunge router. The guide screw of the auger was dead easy to centre over the laid out grid points. The holes are dead straight and clean sided. The auger bit was new which probably helped. As stated I have three rows from an end vise running the length of the front as well as from the front vise and holes in the front apron to support long pieces as well.

Can't say enough about the team at Post Woodworking, Inc., from Karen in the office to the team that... put up this beauty starting at 7AM and were done before lunch, Kyle, Aaron and Billy. After what sounded like a late night at the shop the night prior, they were still on site bright and early as promised and still energized and ready to show their pride in their work. Couldn't be more happy with our 14' x 20' Cohasset. See More
I ended up making a number of practice cuts. The first revealed that I hadn't tightened the screws on the edge guide enough. The second revealed that the design of the edge guide provided very little support at the end of a board, because of the cut-out for the router bit. In the "Getting Started in Woodworking" video, they had screwed a piece of hardwood to the edge-guide, to provide a continuous -- and longer -- bearing surface. I may do that myself, some day, but I didn't have the materials at hand, so I clamped some 2x4 scrap to the end of each board, to provide a continuous bearing surface past the ends. The two grooves in the long stretchers and the side groove in the short stretchers have identical layout. I made practice cuts in scrap until I had the edge guide set correctly, then I cut them all with that one setting. The bottom groove of the short stretchers uses a different setup, so it was back to the scrap, before cutting them.
I am blown away with their ability to teach, a rare characteristic in my opinion, even more so is their passion to do so. I feel that they are able to accurately depict the philosophies and ideas mentioned in your website. My expectations did not even come close to the actual experience I have been given, and that is only in a short short time! I can only dream of what the next 11 months will bring! I am convinced my decision to study at Rowden Farm is the best one I have made to date! Thank you! Much appreciation and gratitude!”
In ancient times, the woodworker’s bench consisted of a plank or split log with four splayed legs. Descendants of those benches are manufactured today, usually with a top of hardwood slabs glued together. The norm nowadays is four straight legs supporting the bulk above, often with braces and a shelf below. Despite the improvements, the linkage to Greek and Roman antecedents is still evident.
Chris I blame you for all these altars that are being built today and now you thinks we over thinks ’em–huh. You whipped the masses into a frenzy— now Woodworkers are trying to out pretty each other–out wood species each other –out Rube Goldberg each other. I made 2 benches in 30 years neither had a through dovetail but many were made on them and I have no idea but I would bet a dollar that neither weighed 280 pounds but they both had tons of wood on them. If you want the bench as a destination god bless but it was intended as a mean. Thats my rant I could be wrong
The 84-906 fits this bill perfectly as the table offers all of the qualities and features that you would expect but does not truly blow you away with any of them. For instance, this bench is made out of rubberwood. This wood is decent in that it provides the strength you want, but it is also extremely porous and rough-grained. The porous nature would generally make it susceptible to rotting and staining, though the bench has been lacquered. The rough grain will potentially cause tools to dull over time if you do not regularly relacquer it.

Getting a smooth, blemish-free finish with oil-based polyurethane is within your grasp if you follow the steps in this article. Oil-based polyurethane varnish brings out the wood’s natural beauty or wood grain. Our 4-step approach shows you how to apply the varnish successfully. A good-quality natural-bristle brush, a reasonably dust-free, well ventilated space and some patience are all you need. Learn how to apply polyurethane.
I built my first platform bed by following the steps mentioned in the tutorial and the end result was everything I expected. It was as beautiful as comfortable and strong. It only cost me around $60 to build this one from the scratch. And if I can build it, anyone can. What you need is a little bit of woodworking experience and a lot of confidence. Collect the items as suggested in the video and start working now.
Build a shed yourself and use it as "on the job training." Those straw built sheds are rinky dink. The people who throw them together are even more sketchy than the finished product. You will be tearing it apart and hauling it out within a few years. Or end up having to reinforce the building with more braces and another layer of flooring. Thats my 99 cents. Its not hard to build a shed especially one of that size. Cowboy up and give it a shot.
×