This is one of those things that you never know you need unless you have one. This amazing wooden sofa sleeve works perfectly on either or both sides of a sofa set. It gives your sofa a nice look. The sleeve can also be modified to include a cup holder, mobile holder, etc. You can easily find this item on any online furniture store, but an even better idea is to build one. This way, you can make a sofa sleeve design that you actually like and make space for cup and other things.
With the shelf secure, get a couple of friends to come help, and stand the bench on its feet. I said earlier moving the top by yourself is dangerous. Trying to lift the entire bench is foolhardy. Of course, I already said I'm stubborn, so I did it myself by rigging a simple block-and-tackle using lightweight pulleys I got at the hardware store. (Not the lightest-weight pulleys, those are meant for flag poles and have a design load of something like 40 pounds. These had a design load of 420 pounds.)

Assemble the vises, for the final time. You'll not be taking them off again, so tighten everything down, and attach the endplate to the ends of the screw and guide rods. Then mark and drill benchdog holes in the outer jaws inline with the benchdog holes in the top. Generally, through-holes are preferred for benchdogs, so that they don't collect sawdust and gunk. With these vises, that isn't possible, there are screws and guide rods in the way. I drilled them just deep enough to hold a Veritas Bench Pony (their reduced-height benchdog), without it sinking to where I can't get a grip to remove it. Rockler sells some very inexpensive plastic benchdogs that can't be adjusted for height, and aren't as strong as metal or wooden dogs, that I intend to keep in the holes full-time, to keep sawdust from collecting in them.
Aside from the privacy it offers, a latticework porch trellis is a perfect way to add major curb appeal to your home for $100 or less. The trellis shown here is made of cedar, but any decay-resistant wood like redwood, cypress or treated pine would also be a good option. Constructed with lap joints for a flat surface and an oval cutout for elegance, it’s a far upgrade from traditional premade garden lattice. As long as you have experience working a router, this project’s complexity lies mostly in the time it takes to cut and assemble. Get the instructions complete with detailed illustrations here.
Once you have all the clamps on, take off the scraps of hardboard. You can clean up the glue squeezeout with a damp rag.. When the glue is dry, trim down the strip flush with the panel using a router and a flush-trim bit. Then cut off the ends of the strip with a flush-cut saw, and clean up with a block plane, an edge scraper, or a sanding block. Leaving the ends in place while you route the edge helps support the router.
Remove the jaws and route the edges that you could not route while they were still attached. Then use a roundover bit on all of the corners except the inner edge of the inner jaw of the end vise. Give everything a lite sanding, and apply Danish oil to the inner surfaces of the jaws. (By "inner surfaces", I mean those surfaces that will not be accessible when the vises are assembled - the inner surface of the inner jaw, that bolts to the bench, and the outer surfaces of the outer jaws, that bolt to the vise plates.)
In terms of size, this bench is another Sjobergs that is a bit on the small side, though it is actually far more squared than some others. While its length is a bit disappointing at 54″, the width is over 24″ wide which does provide for more diverse projects. Even better, this product still features the incredibly 500-pound weight capacity and continues the Sjobergs trend of avoiding joints that are not as durable as they otherwise could be.
In the middle third of the course, you’ll build a tool tote that features dovetails joining bottom-to-end boards; rabbeted and copper-nail pinned side boards; shaped end panels and curved handles passing through angled mortises. This joiner’s tote also features a lift-out box for layout tools with lapped (or optionally dovetailed) corners and a sliding lid.

Can't say enough about the team at Post Woodworking, Inc., from Karen in the office to the team that... put up this beauty starting at 7AM and were done before lunch, Kyle, Aaron and Billy. After what sounded like a late night at the shop the night prior, they were still on site bright and early as promised and still energized and ready to show their pride in their work. Couldn't be more happy with our 14' x 20' Cohasset. See More
This is probably one the easiest woodworking projects you will find here. Although easy, a doormat is an equally important and useful item for households. As you can see in the image below, you will only need some 2X2 wooden boards and rope to build a simple doormat. This doormat is mostly useful for outdoor and porch. It will easily remove all the mud from your shoes with just one wipe. It is also very easy to clean and looks fabulous even if it is dirty.
My wife has given me the OK to buy a "Rancher"-style shed from Lowes and have it installed in the backyard. The discounted installed price will be about $2,600 and this includes the 12' x 8' structure along with a lot of upgrades (twin metal doors, a window, 2 skylights, storage, vents, etc.). I can save about $300 if I build it myself, but my skill level isn't there yet, so I'm going to pay Lowes to assemble it. (See Post #12 below for some photos of the shed and the space I have to work with.)
×